HardwareJacksPotsKnobs |
Click on photo for larger view | Revisit™ VTL5C1 OPTO-ISOLATOR Replaces VTL5C1 from Vactec or Excelitas at an affordable price. Used in many Mesa-Boogie and Crate models in the channel switching circuit. 100dB dynamic range, fast response (2.5ms turn-on), very high dark resistance (50 M Ohm). Light resistance 200 Ohms at 20mA LED current. See datasheet here. Part #VTL5C1 | $4.95 | ||
| 10-Conductor Ribbon Cable 3' Used to interconnect circuit boards in a variety of amps. • 3 inches long • 10 conductors set at 0.1 inch spacing -complete cable is 1 inch wide • Bare wire termination for soldering to PC board at 0.1' hole spacing - no connectors • May be easily cut with an X-Acto knife to make a cable of fewer than 10 conductors. • Not recommended for use in the Fender Hot Rod Deluxe / Deville or Blues Deluxe / Deville. the ribbon cables used in those amps have ribbon cables with conductors set at 0.156' spacing - this cable is too narrow for that application. Part #RJ-310 | $0.99 | ||
Ampeg® & Crate Hardware | ||||
Click on photo for larger view | L-PAD FACE PLATE AND KNOB, for 3/8' diameter threaded bushing found on most L-Pad Level controls. Face plate AND knob only! L-Pad ordered separately. Fits many bass cabinets including the SWR Goliath, Marcus Miller Golight 410, Workingman 8x10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF, SVT-810SPC, BXT210M, BXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, theEngl B115 as well as many others. This is the face plate and knob only - L-PAD itself ordered separately. Raised lettering in charcoal gray instead of white. 3 1/8 inches in diameter, 7/8 inch depth into cabinet. Requires 2 inch diameter hole for mounting. Screws not included. Part #LFP-380 | $3.99 | ||
8 Ohms Click on photo for larger view | L-PAD, 8 Ohms, 3/8' threaded bushing (3/8' long), with plate, knob and hardware. May also be used with the LFP-380 face plate and knob. 8 ohms - for use with 8 ohm speakers, horn drivers or tweeters. L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads, features a 3/8' shaft length, and comes with mounting hardware. This style of L-Pad is found on many popular bass cabinets to control the horn/tweeter level. 2.5 inches in diameter, 1 inch thick. Included face plate is 2 1/8' x 2 1/8'. Part #LPD-262 | $17.95 | ||
16 Ohms Click on photo for larger view | L-PAD, 16 Ohms, 3/8' threaded bushing (3/8' long), with plate, knob and hardware. May also be used with the LFP-380 face plate and knob. 16 ohms - for use with 8 ohm speakers, horn drivers or tweeters. L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 100 watts RMS, is designed to be used with 16 ohm loads, features a 3/8' shaft length, and comes with mounting hardware. This style of L-Pad is found on many popular bass cabinets to control the horn/tweeter level. 2.5 inches in diameter, 1 inch thick. Included face plate is 2 1/8' x 2 1/8'. Part #LPD-261 | $17.95 | ||
Click on photo for larger view | Ampeg® 'a' Logo Used on modern Ampeg Speaker Cabinets, this 3 inch x 4 inch plastic logo is affordably priced. Mounting screws included. Mounting centers are2 ¼' x 2 ⅜'. Part #AL-921 | $4.95 | ||
Click on photo for larger view | Black Logo Mounting Screws Set of 4 logo mounting screws. these are #5 x 7/16' black oxide screws, set of 4. Fit the AL-921 Ampeg logo, and the Fender FAL-912 logo. Part #LS-504 | $0.99 (for a set of 4 screws) | ||
Click on photo for larger view | TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34. Used in many different amplifier brands. 1 1/2' Mounting Centers. Part #TC-142 | $1.79 | ||
Click on photo for larger view | LARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES. Part #TC-143 | $2.89 | ||
Click on photo for larger view | TUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALL. Includes new base, if needed. Spring in top of shield which fits over the tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Ampeg, Crate and many other brands. Holes in base spaced 1 1/8' apart. Shield and base only - socket not included. Part #TS-325S | $1.69 | ||
Click on photo for larger view | TUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALL, SET OF 6. Includes new bases, if needed. Spring in top of shield fits over the tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Ampeg, Crate, and many other brands. Holes in base spaced 1 1/8' apart. Shield and base only - socket not included. Part #TS-325S-6 | $8.95 | ||
(TUBE NOT INCLUDED) Click on photo for larger view | Revisit™ PRE-AMP TUBE DAMPER RINGS. Use two (or three) of these rings around a pre-amp tube to reduce noise and microphonics. An economical alternative to more expensive tube dampers. Will withstand high temperatures of pre-amp tubes, reusable when you change tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes.these dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. Part #PTD-6 | $2.99 (Set of 6 rings) | ||
Click on photo for larger view | Ground Connection Terminals - Flat Made from tin-plated brass - will not rust. Used to connect a ground wire to a screw and nut on a chassis. Flat, with one hole for wire. With built-in lock washer to keep the screw and nut from loosening. Designed for a #8 size screw. Pack of 10 terminals. Part #2310915 | $2.99 (Pack of 10 terminals) | ||
Click on photo for larger view | TERMINAL STRIPS, 6 LUG, SET OF 2. Perfect for amplifier circuit additions or modifications. End terminals on each strip are the mounting lugs, so they become a ground lug if attached to a metal chassis. Each terminal strip is 2 1/4 inches long. the lugs are set on 3/8 inch centers. Each lug will accept wires up to 16ga - smaller gauge allows multiple wires to be connected to each lug. Set contains 2 terminal strips as pictured. Mounting hardware not included. Part #2320822 | $2.89 (for a set of 2 terminal strips) | ||
Click on photo for larger view | CUP WASHER, BLACK METAL, PACK OF 10. USED WITH #8 BLACK SCREW ON AMP AND SPEAKER CABINETS. Part #BCW-10 | $1.29 (pack of 10) | ||
Click on photo for larger view | SPEAKER BAFFLE MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Locking nut and washer included. Phillips head. Drill hole, insert and tighten screws into wood from front of baffle. Install grill cloth, and you have professional speaker mounting studs. Set of 4. Part #SC-409-4 | $2.29 (For a pack of 4 screws with nuts and lock washers) | ||
Click on photo for larger view | ISOLATION WASHER - 3/8' 3/8' outside diameter neoprene bonded flat washer. Perfect for bolting speakers to cabinets. It will securely hold the speaker in place and stop any rattling. For use with #6 and #8 screws. Set of 4 washers. Part #SIW-38-4 | $0.59 (For a set of 4 washers) | ||
Click on photo for larger view | BLACK PAN-HEAD WOOD SCREWS, #6 X 3/4', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #6 screw, 3/4 inch long, pack of 10. Part #SCR-435 | $0.79 (pack of 10) | ||
BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 1/2 inch long, pack of 10. Part #BWS8-5 | $0.89 (pack of 10) | |||
BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 3/4 inch long, pack of 10. Part #BWS8-75 | $0.95 (pack of 10) | |||
BLACK PAN-HEAD WOOD SCREWS, #8 X 1', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 1 inch long, pack of 10. Part #BWS8-1 | $1.05 (pack of 10) | |||
BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 1-1/2 inches long, pack of 10. Part #BWS8-15 | $1.19 (pack of 10) | |||
Click on photo for larger view | CAGE NUT, ZINC, 10-32 THREAD. Used on square-punched amp chassis rails to secure the chassis to the cabinet. Frequently found in Peavey, Crate, Ampeg, other brands. NOT used in Marshall® - see the MCN-4. Works with all 10-32 screws. Verify screw thread before ordering, as not all cage nuts are 10-32. Zinc coating retards oxidation. Pack of 4 nuts. Made in Canada by Hammond Industries. Part CNA-1421 | $4.29 (pack of 4) | ||
Click on photo for larger view | SMALL BLACK RUBBER FEET, PACK OF 4. 3/4' DIAMETER AT TOP, 5/8' DIAMETER AT BOTTOM, 5/16' TALL. BLACK RUBBER WITH METAL INSERT. USED TO SUPPORT EFFECTS, SMALLER AMPS, SMALLER MIXERS. SCREWS NOT INCLUDED. Part #BRF-4 | $2.95 (pack of 4) | ||
Click on photo for larger view | SMALL BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for smaller amps, amp heads, or speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. Just under 1 inch - 15/16' diameter at the top, rounded down to 5/8' diameter at the bottom, and 3/8' tall. Screws not included. Set of 4 feet. Part #BRF-723 | $3.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for large rack cabinets or speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter x 1' tall. Mounting screws not included. Part #BRF-1691 | $4.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for rack-mount amps, combo amps, or small speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter (wide end) x 3/4' diameter (narrow end) x 0.85' tall. Mounting screws not included. Set of 4 feet. Part #BRF-9105 | $4.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter x 5/8' tall. Mounting screws not included. Part #BRF-1692 | $4.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 5. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter x 5/8' tall. Mounting screws not included. This set of 5 works well for the main feet used on the Ampeg BA-210 when the cabinet is in the upright position. Part #BRF-1692-5 | $6.25 (pack of 5) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 4. Tapered: 1 3/16' Diameter At Small End, 1 1/4' Diameter At Large End. 1/2' Tall. Black Rubber With Metal Insert. Used To Support Effects, Amps, Mixers. Mounting Screws Not Included. Part #BRF-9112 | $4.95 (pack of 4) | ||
Click on photo for larger view | X-LARGE BLACK RUBBER FEET, SET OF 4. Tapered - 1 5/8' Diameter At Large End, 1 1/4' At Small End. 3/4' Tall. Black Rubber With Metal Insert. Used To Support Amp Heads, Speaker Cabinets. Mounting Screws Not Included. Part #BRF-9107 | $7.95 (pack of 4) | ||
Click on photo for larger view | Fender® Style Flat Mount 2' Caster Wheels - Set of 4. Great for Fender® and many other brands of amps or cabinets. Each wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2' in diameter. Specifications found here. Note: Mounting screws NOT included. Part #FCW-4F | $24.95 (Set of 4 casters) NOT SOLD OUTSIDE the USA | ||
Click on photo for larger view | Fender® Style Pop-Out 2' Caster Wheels - Set of 4. Great for Fender® and many other brands of amps or cabinets. Each wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2' in diameter. the same type of removable caster wheels used on Fender® amps since the 1960s. Note: Mounting screws NOT included. Must drill 5/8' hole in bottom of cabinet to accomodate post for wheel. Part #FCW-4R | $28.95 (Set of 4 pop-out casters) NOT SOLD OUTSIDE the USA | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, BLACK WITH BLACK STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8-9/16 inches (8.57'), center-to-center mounting distance is 7-3/8 inches (7.38') Black with black stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-281 | $12.95 | ||
'SHORTY' AMP HANDLE Click on photo for larger view | Revisit™ 'SHORTY' AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, BLACK WITH BLACK STITCHING Similar to the AH-281 handle above, but 1-3/4 inches shorter. Handle length is 6-13/16 inches (6.80'), center-to-center mounting distance is 6 inches (5.98') Black with black stitching, nickel mounts. Mounting screws not included - use SC-402 screw pack. This is a great handle to consider for smaller combo amps, practice amps, etc. Delivers a professional quality look and reliability in a smaller size for smaller amps. More details Part #AH-281-S 'Shorty' | $8.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, DARK BROWN WITH BROWN STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Dark brown with brown stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-270 | $12.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, TAN WITH TAN STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Tan with tan stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-108 | $12.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, DARK BROWN WITH WHITE STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Dark brown with white stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-318 | $12.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, DEEP NAVY BLUE-GREY WITH WHITE STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Dark navy blue-grey with white stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-319 | $12.95 | ||
Click on photo for larger view | Fender® or Ampeg® VINTAGE STYLE GUITAR AMP HANDLE, RAISED, BLACK STITCHED SIMULATED LEAtheR.Black handle strap, made of simulated leather, replacement for Fender® 'tweed' style amps or vintage Ampeg amps (as well as other vintage amps. Has slight 'raised' bump near the center of the handle. Black, white stitched. 6-1/4 to 6-1/2 inches between mounting posts. Total length 8-3/4'. Mounts and screws are included. Part #GAH-782 | $15.95 | ||
Click on photo for larger view | Revisit™ BLACK GUITAR AMP HANDLE, WITH HARDWARE. Rugged rubber black handle strap, steel reinforced. Black metal caps. Black 10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8'wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is 10 1/4'. Part #GAH-271B | $7.99 | ||
Click on photo for larger view | Revisit™ GUITAR AMP HANDLE - BLACK. Rugged rubber black handle strap, steel reinforced. Black metal caps. Screws not included - recommend using our SC-403B 10-32 type screws along with a 10-32 T-Nut for secure mounting. Handle strap is 7/8' wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is 10 1/4'. Part #GAH-1 | $6.99 | ||
| BLACK HANDLE SCREWS Pack of 2 stainless-steel handle screws finished in satin black for use with black end-cap handles, such as our GAH-1, OAH-456, or GAH-271B. 1' Long, 10-32 threads, finished in satin black to match black end caps. Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4' or less. Will not work with external nut - must be a T-Nut. Will not work with cabinet wood thicker than 3/4'. See Data Sheet here Part #SC-403B | $0.99 (for a pack of 2 screws) | ||
Click on photo for larger view | Revisit™ CHROME/BLACK GUITAR AMP HANDLE - CHROME, WITH HARDWARE. Rugged rubber black handle strap, steel reinforced. Chrome metal caps. 10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8'wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is 10 1/4'. Not recommended for Fender, as the screws are set too far apart for Fender® amp specifications. Part #GAH-271C | $7.99 | ||
| HANDLE SCREWS Pack of 2 stainless steel handle screws for GAH-271C Handle. 1' Long, 10-32 threads. Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4' or less. Will not work with external nut - must be a T-Nut. Will not work with cabinet wood thicker than 3/4'. See Data Sheet here Part #SC-403 | $0.99 (for a pack of 2 screws) | ||
Click on photo for larger view | LARGE SIZED STRAIN RELIEF FOR 35/64' X 5/8' HOLE Popular strain relief found on most vintage guitar amplifiers with round power cords. Designed for 5/16' cord diameter. Click here for specific dimensions of chassis hole. For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below. Part #SR-1200 | $0.99 | ||
Click on photo for larger view | STRAIN RELIEF INSTALLATION/REMOVAL TOOL Removing and installing strain reliefs can be a frustrating job. Standard pliers just do not get the job done and can damage the strain relief. these special strain relief pliers are just what you need. they fit perfectly on AC power cord strain reliefs and give you the leverage you need to compress the strain relief for easy removal and installation, without damage. Part #YTH-205 | $12.95 | ||
Click on photo for larger view | EXTRA-LARGE SIZED STRAIN RELIEF FOR 3/4' X 27/32' HOLE Popular strain relief found on a few larger vintage bass amplifiers and power amplifiers with very thick power cords. Designed for 11/32' cord diameter. Click here for specific dimensions of chassis hole. Part #SR-1300 | $0.99 | ||
Click on photo for larger view | SMALL RUBBER CHASSIS GROMMET FOR 3/8 INCH CHASSIS HOLE (GROMMET INNER HOLE 1/4 INCH) Chassis grommet, for electrical insulation, wire protection and management, shock absorption, or mechanical isolation. This grommet has a 1/4 inch diameter inner hole, and mounts in a 3/8 inch chassis hole. Full datasheet here. Part #RCG-739 | $0.49 each | ||
Click on photo for larger view | LARGE RUBBER CHASSIS GROMMET FOR 1/2' CHASSIS HOLE (GROMMET INNER HOLE 3/8 INCH) Chassis grommet, for electrical insulation, wire protection and management, shock absorption, or mechanical isolation. This grommet has a 3/8 inch diameter inner hole, and mounts in a 1/2 inch chassis hole. Full datasheet here. Part #RCG-745 | $0.49 each | ||
Ampeg Fans | ||||
Click on photo for larger view | thermoCool Fan. 80 x 38mm Sleeve Bearing 19 CFM. thermocool axial fans provide enhanced cooling for a variety of electronic devices. Leading air flow technology is designed into every thermocool product resulting in reduced turbulence, low noise levels and a more energy efficient product. thermocool fans are ideal for use in computer systems, portable CD and DVD players, stereo components, overhead projectors, laptop computers, and many other electronic applications where circulation is a key concern. This fan is the replacement for the fan used in the Ampeg SVT Classic, Ampeg® part number 24-321-03. Specifications: • Power: 120V AC, 60 Hz • Sleeve bearing • Lead wire connection • 0.13 amps • 2400 RPM • 28dB noise level • 23 CFM air flow • Dimensions: 80 mm (H) x 80 mm (W) x 38 mm (D) [3 1/4' (H) x 3 1/4' (W) x 1 1/2' (D)] For use on 110-120VAC System only, as found in North America. Part #G8038HAS | $19.95 | ||
Ampeg® & Crate® Jacks | ||||
Click on photo for larger view | JACK, 1/4', CHROME NUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-SLEEVE, 4 PINS. Generally found only in Crate or Ampeg products.Common input, footswitch or effects loop jack exclusive to Crate® and Ampeg®. (Other brands with chrome-nut jacks use a straight pin jack such as the J-580.) 4 pins, PC mount, with chrome nut and washer. Note 'L-Leg' pins as shown in photo. Original Crate or Ampeg part number 39-119-01. Part #J-580L | $3.95 | ||
Click on photo for larger view | JACK, 1/4', CHROME NUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE, L-LEG, TIP-SLEEVE, 4 PINS, GOLD CONTACTS. Generally found only in Crate or Ampeg products.Common input, footswitch or effects loop jack exclusive to Crate® and Ampeg®. (Other brands with chrome-nut jacks use a straight pin jack such as the J-580.) 4 pins, PC mount, with chrome nut and washer. Gold contacts for improved conductivity, performance, and reliability. Note 'L-Leg' pins as shown in photo. Part #J-580LG | $4.95 | ||
Click on photo for larger view | JACK, 1/4', CHROME NUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF UK, L-LEG, TIP-RING-SLEEVE, 6 PINS. Generally found only in Crate or Ampeg products.Common input, footswitch or effects loop jack exclusive to Crate®, Ampeg®. (Other brands with chrome-nut jacks use a straight pin jack such as the J-581.) 6 pins, PC mount, with chrome nut and washer. Note 'L-Leg' pins as shown in photo. Original Crate or Ampeg part number 39-120-01. Part #J-581L | $4.50 | ||
Click on photo for larger view | JACK, 1/4', INPUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-SLEEVE, 4 PINSCommon input jack in Crate®, Ampeg®, others. Ampeg and Crate® part number 39-116-01. 4 pins, PC mount, with nut and washer. Note 'L-Leg' pins as shown in photo. Part #J-503L | $3.79 | ||
Click on photo for larger view | JACK, 1/4', INPUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-RING-SLEEVE, 6 PINCommon input jack in Crate®, Ampeg®, others. Ampeg and Crate part number 39-117-01. 6 pins, PC mount, with nut and washer. Note 'L-Leg' pins as shown in photo. Part #J-504L | $3.95 | ||
Click on photo for larger view | JACK NUT, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall® AND OtheRS. Note: Replaces most black plastic jack nuts EXCEPT for Roland. Will NOT fit Roland jacks. Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks. Also fits the J-518 and J-519 jacks. Part #J-5NT | $0.50 | ||
Click on photo for larger view | JACK NUT MULTI-PACK - SAVE! 6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall® AND OtheRS. Note: Replaces most black plastic jack nuts EXCEPT for Roland. Will NOT fit Roland jacks. Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks. Also fits the J-518 and J-519 jacks. Part #J-5NT-6 | $2.39 | ||
Click on photo for larger view | JACK NUT/FERULE, CHROME, with BLACK PLASTIC BEZEL/WASHER - GENUINE CLIFF UK Replacement nut and bezel washer for the J-501, J-501S, J-580, J-581, J-580L and J-581L jacks. Note: the threads on this nut are coarse (3/8-20), and are for genuine Cliff jacks. Note: there are some generic jacks on the market with finer thread nuts. This nut will not fit those jacks. This nut is for genuine Cliff UK jacks. Bezel is included with this nut. Part #JN-200W | $0.79 | ||
Click on photo for larger view | JACK NUT/FERULE, BLACK, with INTEGRAL BLACK PLASTIC BEZEL - GENUINE CLIFF UK Replacement nut and bezel washer which will fit the J-501, J-501S, J-580, J-581, J-580L, J-580LG, and J-581L jacks. Note: the threads on this nut are coarse (3/8-20), and are for genuine Cliff jacks. Note: there are some generic jacks on the market with finer thread nuts. This nut will not fit those jacks. This nut is for genuine Cliff UK jacks. Bezel is integral to the nut and cannot be removed. This is the jack nut used on the Marshall JMP-1 Preamp, and on some versions of the Marshall DRP-1 Direct Recording Preamp. Part #JN-864 | $0.79 | ||
Click on photo for larger view
| JACK, 1/4', PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED. Both tip and ring conductors are switched (normally closed). Used in Crate® and other brands. NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW. Part #J-527 | $4.50 | ||
JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 | $0.89 (Set of 1 washer and 1 nut) | |||
| Dual Chassis-Mount Banana Binding Posts. Used on the rear panel of many power amplifiers and some bass amps, such as the Ampeg B4R. Red and black posts, accepts either single or dual banana plugs. Mounts in two 1/2' holes on 3/4' centers, panel thickness up to 1/4'. 15A rating, gold plated contacts. | $4.99 | ||
Click on photo for larger view | JACK, 1/4', MONO, OPEN CIRCUIT, WIRED, Switchcraft® Found in many guitars, effects pedals, amps speaker output. Includes nut and washer. Part #J-11 | $2.25 | ||
Click on photo for larger view | JACK, 1/4', MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft® Found in vintage amps as the input jack. Includes nut and washer. Part #J-12A | $2.79 | ||
Click on photo for larger view | JACK, 1/4', TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft® Used with T/R/S plugs for either balanced connections or stereo connections. Also very common in guitars with active pickups, and as the input jack on some effects pedals. the ring conductor is used in these cases to 'turn on' the battery by tying one leg of the battery to ground via the plug. Part #J-12B | $2.99 | ||
Click on photo for larger view | JACK, 1/4', TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING Same as the J-12B jack, but with longer (3/8') threaded bushing for mounting in thicker panels. Includes nut and washer. Part #J-L12B | $3.99 | ||
Click on photo for larger view | JACK, 1/4', TIP/RING/SLEEVE, WITH TIP SHUNT. Switchcraft 13B Jack. Tip/Ring/Sleeve Switchcraft jack. Tip has a shunt contact, ring contact is open circuit. Part #J-13B | $6.95 | ||
Click on photo for larger view | JACK, 1/4', MONO, CLOSED CIRCUIT, RIGHT ANGLE PC MOUNT, Switchcraft® STYLE, NYLON THREADS, 3 PINS Common input jack in Crate® & Ampeg®, and in some solid state products from Fender® during the early 1980s. Nut and washer included. Part #RN112APC | $5.79 | ||
Click on photo for larger view | JACK, 1/4', STEREO, CLOSED CIRCUIT, RIGHT ANGLE PC MOUNT, Switchcraft®STYLE, NYLON THREADS, 5 PINS Common input jack in Crate® & Ampeg® products. Nut andwasher included. Switchcraft RN114BPC. Nut and washer included. Part #J-114PC | $5.99 | ||
Click on photo for larger view | SAVE WITH MULTIPACK! JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6 Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Set of 6 washers and 6 nuts. Part #JNUT-38-6 | $4.50 (Set of 6 washers and 6 nuts) | ||
JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 | $0.89 (Set of 1 washer and 1 nut) | |||
| JACK, 1/4', TIP/RING/SLEEVE, 7 PIN, PC MOUNT, Fender®, Hartke® and Crate® Amps. Fender®, Hartke® or Crate® PCB mount 1/4' jack. 7 pins. Fits several Hartke® amp models 1990 - present, and several Crate® models, especially in the GX series. Used in the Fender® SKX65R and SKX100R for the input jacks. Used in some Fender® Squier and Sidekick amps as the headphone jack. Hartke® part number 350023 and 300519. Fender® part number 022923. NUT & WASHER NOT INCLUDED - ORDER JN-916. | $6.95 | ||
NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE. | $0.39 | |||
SAVE WITH MULTIPACK! NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE, SET OF 6. | $2.09 | |||
Click on photo for larger view | JACK, 1/4', Peavey® PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING. Both tip and ring conductors are switched (normally closed). 5 pins. Original Peavey® part number 31466217. Used in Peavey®, Mackie, Fender, Crate, Ampeg and other brands. Replaces Switchcraft 114BPCX and 114BPCSX. Nut and washer on this jack ARE included. Part #J-529 | $2.99 | ||
Click on photo for larger view
| JACK, 1/4', PC MOUNT, STEREO, 4 PINS, SWITCHED, METAL BUSHING. Tip is switched (normally closed), ring conductor is not switched. Made by Neutrik/Rean. Used in a variety of brands. Replaces Switchcraft. NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW. Part #J-524A | $3.50 | ||
Click on photo for larger view | SAVE WITH MULTIPACK! JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6 Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Set of 6 washers and 6 nuts. Part #JNUT-38-6 | $4.50 (Set of 6 washers and 6 nuts) | ||
JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 | $0.89 (Set of 1 washer and 1 nut) | |||
Click on photo for larger view. Jack is in the picture to demonstrate how the washers are installed - jack is NOT included with the washers. | INSULATING SHOULDER WASHER, FIBER Pair of fiber insulating shoulder washers for Switchcraft jacks with metal bushings. Used to mount standard jacks in a 1/2' diameter chassis hole, while insulating the metal bushing (ground) of the jack from the chassis. ID 3/8', OD 1/2'. Works great when replacing isolated plastic jacks with a more durable metal jack, which is frequently done on the input jacks of the Fender® Hot Rod Deville/Deluxe and Blues Deville/Deluxe. Two washers are used on each jack, and the 'shoulders' are placed facing each other through the chassis. the washers not only isolate the ground of the jack electrically for noise reduction, but also stabilize the jack in the 1/2' diameter hole. Jack shown in picture NOT included. Works well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13, J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks. Part #ISW-3069 | $0.49 (For a pair of washers. Each jack needs two washers.) | ||
Click on photo for larger view | JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR PC BOARD (SOLDER PINS). Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including Ampeg®. Part #J-NL4MD-V | $4.95 | ||
Click on photo for larger view | JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR WIRE ATTACHMENT (3/16' PUSH ON CONNECTORS OR SOLDER TABS). Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including Ampeg®. Part #J-NL4MP-2 | $4.95 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for speaker cabinets with one speaker. Includes Switchcraft #11 jack, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. For two-speaker cabinets, see the SCH-2411X2, below. Part #SCH-2411 | $10.49 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE FOR TWO SPEAKER CABINET. Preassembled for speaker cabinets with two speakers in parallel. Includes Switchcraft #11 jack, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors, plus an additional 24' jumper cable. Part #SCH-2411X2 | $14.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH 1/4' STRAIGHT PLUG and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for combo amps with one speaker. Includes 1/4' straight plug, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. For 2-speaker cabinets, add the SJ-150 jumper, below. Part #SCH-224 | $10.49 | ||
Click on photo for larger view | Revisit™ SPEAKER JUMPER CABLE polyvinyl insulated silver plated copper speaker wire, 18 gauge, twisted pair, black and white. Terminated at each end in standard 3/16' speaker fast-on connectors. Great for connecting speakers in parallel in 2x12 or 4x12 cabinets. 24 inches (61 cm) long. Made in USA. Part #SJ-150 | $5.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH 1/4' RIGHT-ANGLE PLUG and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for combo amps with one speaker. Includes 1/4' straight plug, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. For 2-speaker cabinets, add the SJ-150 jumper, above. Part #SCH-287 | $10.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS, 2 ft LONG, RIGHT-ANGLE PLUG TO BARE TINNED WIRE, 16 GAUGE CABLE Replacement right-angle plug with 24' cable and stripped, tinned bare wire. Used to replace speaker cable in many combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4' jack and plug. Heavy-duty 16ga round black speaker cable, right-angle plug and bare wire ready for soldering to one speaker. Part #SCH-7090 | $4.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS Replacement right-angle plug with 34' cable and 3/16' fast-on connectors. Used to replace speaker cable in most combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4' jack and plug. 18ga black zip cord, right-angle plug and fast-on connectors for attachment to one speaker. Part #SCH-280 | $6.50 | ||
Click on photo for larger view | Revisit™ SPEAKER CABLE - HEAD TO CABINET - 4 FEET LONG Black 4 feet 16 gauge speaker cable, with one straight 1/4 inch plug and one right-angle 1/4 inch plug. Used to connect amplifier head to cabinet. Part #SCH-7028 | $4.99 | ||
Click on photo for larger view | JACK PLATE, BLACK METAL, SINGLE 1/4' JACK, 2' OUTSIDE DIAMETER. Similar in style to vintage Fender® jack plates. Works well with the Switchcraft J-11 1/4' jacks that we carry. Hole is 3/8', for most Switchcraft type jacks. Easy to install, economical. Includes 3 black oxide coarse-thread mounting screws, #6x3/4'. Jack not included - order separately. For size specifications, click here. Part #JP-180 | $1.49 | ||
Click on photo for larger view | Revisit™ JACK PLATE COMPLETE WITH SWITCHCRAFT #11 JACK. Switchcraft #11 jack preinstalled with lock washer and trim washer. Outside diameter 2 inches (51mm). Designed to fit flush against a 1 1/8' (29mm) cabinet hole. Easy to install - drill 1 1/8' hole in cabinet, attach speaker wiring to jack and speaker, attach plate to cabinet. Part #JPC-180 | $4.95 | ||
Click on photo for larger view | Revisit™ JACK PLATE COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE. Preassembled - includes 2' diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. Outside jack plate diameter 2 inches (51mm). Designed to fit flush against a 1 1/8' (29mm) cabinet hole. Easy to install - drill 1 1/8' hole in cabinet, attach speaker wiring to speaker, attach plate to cabinet. For two-speaker cabinets, see the JPH-182, below. Part #JPH-180 | $11.95 | ||
Click on photo for larger view | Revisit™ JACK PLATE COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE, PLUS ADDITIONAL 24' JUMPER. Preassembled - includes 2' diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. Outside jack plate diameter 2 inches (51mm). Designed to fit flush against a 1 1/8' (29mm) cabinet hole. Includes a second 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors to connect to a second speaker in the same cabinet. Easy to install - drill 1 1/8' hole in cabinet, attach speaker wiring to speakers, attach plate to cabinet. Part #JPH-182 | $15.95 | ||
Click on photos for larger views | JACK PLATE, MONO/STEREO, PLUG AND PLAY This unit eliminates the confusing switch found on most stereo cabinets. Just pick your impedance and plug in. Labels shows the common 4 or 16 Ohm Mono and 8 Ohm Stereo option. Ready to install with a steel dish, wires, and speaker connectors already assembled - as shown in the photo. Requires a 3 inch x 3-7/16 inch rectangular hole cut in the cabinet. Direct easy replacement for many existing small jack dishes. No soldering required. Complete wiring directions included - click here for more details. Designed to be used with 2x12 cabinets containing two 8-ohm speakers, 4x12 cabinets with four 16-ohm speakers, or 4x12 cabinets with four 4-ohm speakers. Can be used for the following configurations:
Part #CJP-1 | $25.95 | ||
Ampeg Knobs | ||||
Click on photo for larger view | KNOB, Ampeg®, Classic Genuine Ampeg® amp knob, black with white pointer. Fits pots with 1/4' D-shaft type shafts. Part #K-324 | $5.95 | ||
Ampeg Relay | ||||
Click on photo for larger view | RELAY, Ampeg®, SVT-4PRO and other models Protection relay used in the SVT-4PRO. Common failure item - contacts become oxidized or burned and fail to connect the speakers to the power amp, even when the relay clicks in. there are two of these relays in the SVT-4 PRO, at locations K-101 and K-201. Original Ampeg part number 82-090-01 Part #82-090-01 | $18.95 | ||
Crate® Pots | ||||
Crate Amplifiers is no longer in business as of 2018, and potentiometers for their amps are no longer available. | ||||
Ampeg® & Crate® AC Power | ||||
Click on photo for larger view | IEC POWER CONNECTOR, AMPEG®, NON-FUSED, PCB MOUNT Used in the Ampeg® SVT-3-PRO, SVT-4-PRO, SVT-5-PRO, SVT-6-PRO, B2R, B4R, B5R bass amplifiers. Original Ampeg® part number 17-604-01. Datasheet here. Part #17-604-01 | $4.95 | ||
Click on photo for larger view | Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END. COMMON REPLACEMENT CORD FOR MANY GUITAR AMPS, POWER AMPS, EFFECTS UNITS, ETC.Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. IEC connector at equipment end. Used only in North America. Part #PC-300 | $5.95 | ||
Click on photo for larger view | Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END. Replacement Cord For Many Guitar Amps, Power Amps, Effects Units, Etc. 10 Ft Length Give Extra Flexibility In Equipment Placement, Reduces Use Of Extension Cords. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. IEC connector at equipment end. Used only in North America. Part #PC-600 | $10.95 | ||
Click on photo for larger view | SUPER-LONG Revisit™ 4 METER (about 13 ft) POWER CORD, 3-WIRE, 18ga, SVT type, 'Thin Line'. OUR LONGEST POWER CORD! Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length is a super-long 13 feet, cord thickness is 0.24 inches (about 1/4' or 6.2mm). Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SVT13-TL | $14.95 | ||
Click on photo for larger view | EXTRA-LONG Revisit™ 12 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length is an extra-long 12 feet, cord thickness is 0.29 inches(about 9/32' or 7.3mm). This cord is of appropriate gauge and physical thickness for application in most medium to large guitar amps with 'hard-wired' power cords. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SJT12 | $13.95 | ||
16 gauge: Click on photo for larger view | LONG 10 ft POWER CORD, 3-WIRE, 16ga, SJT type. Cut end for installing (soldered connection) into many vintage large power amps or large bass amps using a 3-wire cord. This 16 gauge cord is not normally used on guitar amps, as they do not require the heavy 16 gauge. Cord length is 10 feet, cord thickness is 0.32 inches (about 5.6' or 8.1mm), wire gauge is 16ga. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-163SJT10 | $12.95 | ||
18 gauge: Click on photo for larger view | LONG 10 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut end for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length is 10 feet, cord thickness is 0.29 inches (about 9/32' or 7.3mm). This cord is of appropriate gauge and physical thickness for application in most medium to large guitar amps with 'hard-wired' power cords (Fender, for example). Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SJT10 | $11.95 | ||
Click on photo for larger view | Revisit™ 8 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length 8 feet, cord thickness is 0.29 inches (7.3mm). Part #PC-183SJT8 | $9.95 | ||
Click on photo for larger view | 8 ft POWER CORD, 3-WIRE, 18ga, SVT type, 'Thin Line'. Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length 8 feet, 18 gauge, cord thickness is 0.24 inches (about 1/4' or 6.1mm). Thinner than the PC-183SJT8 cord, this cord is better suited for replacing amp cords in smaller amplifiers where there was formerly a 2-wire cord without ground. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SVT8-TL | $9.95 | ||
Click on photo for larger view | Fender® style reverb or AC cable clamp. Used on Fender amps since the early 60s to hold the reverb cable to the side of the cabinet. Clamp is 3/8' diameter, comes with 3/4' screw for mounting. Also used in some amplifiers to hold the AC cord to the cabinet wall. Fender® part number 022941. Works on many other brands of amplifiers as well. Part #RCC-381 | $0.99 | ||
Ampeg® & Crate® Reverb Tanks | ||||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 3 spring, equivalent to Accutronics 9AB2C1B. Input impedance 10 ohms, output impedance 2575 ohms, medium decay (1.75 - 3 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Hughes & Kettner®, MarshallTM, Ampeg, Crate, Fender®, Mesa Boogie, Guytron, Rocktron, DOD, Summit Audio, and Smokey. See explanation of Accutronics reverb tank numbering systemhere. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #9AB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $38.99 In stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 3 spring, equivalent to Accutronics 9EB2C1B. Input impedance 800 ohms, output impedance 2575 ohms, medium decay (1.75-3.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Hughes & Kettner®, MarshallTM, Ampeg, Crate, Fender®, Mesa Boogie, Guytron, Rocktron, DOD, Summit Audio, and Smokey. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #9EB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $38.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4AB3A1B. Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input grounded/output grounded, designed for horizontal mounting, open side down. Replacement for the Gibbs Type F reverb tanks used in the 60's and early 70's, including Ampeg models Echo Jet, Echo Twin, B12X, B12XY. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty detailshere. Part #4AB3A1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4AB3C1B. Input impedance 10 ohms, output impedance 2575 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Hughes & Kettner®, MarshallTM, Ampeg, Crate, Fender®, Mesa Boogie, Guytron, Rocktron, DOD, Summit Audio, and Smokey. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4AB3C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Accutronics Reverb Tank, 17' long, 2 spring, 4AB3C1B current production. Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Primarily used by all Fender® amplifiers with tube reverb from 1963-1990. Also used in Reissue models like: Fender® Princeton Reverb, Fender® Deluxe Reverb, Fender® Vibrolux Reverb, Fender® Pro Reverb, Fender® Super Reverb , Fender® Twin Reverb, Fender® Quad Reverb , Fender® Super Six Reverb,Fender® Vibrosonic , Fender®`63 Reverb Unit Reissue, Fender®`65 Princeton Reverb Reissue,Fender®`65 Deluxe Reverb Reissue, Fender®`65 Super Reverb Reissue, Fender®`65 Twin Reverb Reissue, Fender® 65 Twin Custom(TM) 15, Fender® Concert II, Fender® Dual Professional. Also used in Mesa Boogie® MK2C and others, LAB Series L5, L7, L9,Koch® Powertone I, Ampeg® VT-40, Ampeg® Super Rocket SR212 and B-52® AT-100. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Accutronics products are made in South Korea. Part #ACC-4AB3C1B | $35.99 | ||
Click on photo for larger view | Belton Reverb Tank, 17' long, 2 spring, 4AB3C1B, current production. Belton part number BL2AB3C1B. Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Primarily used by all Fender® amplifiers with tube reverb from 1963-1990. Also used in Reissue models like: Fender® Princeton Reverb, Fender® Deluxe Reverb, Fender® Vibrolux Reverb, Fender® Pro Reverb, Fender® Super Reverb , Fender® Twin Reverb, Fender® Quad Reverb , Fender® Super Six Reverb,Fender® Vibrosonic , Fender® 63 Reverb Unit Reissue, Fender® 65 Princeton Reverb Reissue,Fender® 65 Deluxe Reverb Reissue, Fender® 65 Super Reverb Reissue, Fender® 65 Twin Reverb Reissue, Fender® 65 Twin Custom(TM) 15, Fender® Concert II, Fender® Dual Professional. Also used in Mesa Boogie® MK2C and others, LAB Series L5, L7, L9,Koch® Powertone I, Ampeg® VT-40, Ampeg® Super Rocket SR212 and B-52® AT-100. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Belton products are made in South Korea. Belton part number BL2AB3C1B. Part #BL-4AB3C1B | $32.99 | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB2C1B. Input impedance 150 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4BB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB3C1B. Input impedance 150 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting. Upgrade for Crate part number 79-201-02 - tank for the Crate V-32 Palomino and Vintage Club 30 / VC3112. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4BB3C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB3C1D. Input impedance 150 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for vertical mounting, connectors down. Common replacement for MarshallTM, Ampeg, Crate. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4BB3C1D 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4EB2C1B. Input impedance 600 ohms, output impedance 2250 ohms, medium decay (1.75 - 3 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Ampeg, Crate V50 Palomino. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4EB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2B1A. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input grounded/output insulated. Mounts horizontal, open side up. Common replacement in vintage Ampeg. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2B1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2D1A. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input isolated/output isolated, designed for horizontal mounting, open side up. Used in some versions of the Ampeg V4. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2D1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2D1B. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input isolated/output isolated, designed for horizontal mounting, open side down. Used in some versions of the Ampeg V4. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2D1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2C1C. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input isolated/output isolated, designed for designed for vertical mounting, long axis horizontal, connectors up. Common replacement for Ampeg VT-22. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2D1C 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3A1A. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input grounded/output grounded, designed for horizontal mounting, open side up. Common replacement for certain versions of the Ampeg Gemini and also found in some vintage Kustom amps from the 1960s and early 70s. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3A1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3A1B. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input grounded/output grounded, designed for horizontal mounting, open side down. Common replacement for Ampeg and Music Man. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3A1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3D1A. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input isolated/output isolated, designed for horizontal mounting, open side up. Used in some versions of the Ampeg V4. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3D1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3D1B. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input insulated/output insulated, designed for horizontal mounting, open side down. Common replacement for Ampeg and Music Man. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3D1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8AB2A1B. Short Tank, Medium Decay, input impedance 10 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8AB2A1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8BB2A1B. Short Tank, Medium Decay, input impedance 190 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down. Primarily used by Crate and Ampeg. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8BB2A1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8BB2C1B. Short Tank, Medium Decay, input impedance 190 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down. Primarily used by Rivera PUBSTER 25 & CHUBSTER 40 , Rivera Knucklehead Reverb, Vox® AC30, with solid state reverb as used in the Seventies, Ampeg® Jet II J12R, Crate® G212, Crate® GT212, Crate® Palomino V32 & V16, Music Man® RD50, Kitty Hawk Supreme, Marshall® G80RCD, Marshall® G100RCD. Upgrade for Laney® VC15 (part nr. 10006), Brunetti Singleman, Mesa Boogie® Rectoverb. Replaces Ampeg® / Crate® part number 79-201-02. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8BB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8EB2C1B. Short Tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down. Used in Crate, Fender, Peavey, Music Man. This is the most popular short tank. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8EB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8EB2C1E. Short Tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts vertical wall, long axis vertical. Used in Crate® Tube Driver series of amps, such as the TD-70. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8EB2C1E 'Bringing back the sound of vintage Accutronics tanks' | $33.99 | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8FB2A1B. Short Tank, Medium Decay, input impedance 1925 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down. Primarily used in Crate Amps. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8FB2A1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Rubber mounting grommets for reverb tanks, package of four. Provides shock absorption for tanks mounted directly to the inside of a wooden amp cabinet. Mounting Hole Diameter = 3/8' Outer Diameter = 1/2' Part #RRG-4 | $1.99 (For a pack of 4 grommets) | ||
Click on photo for larger view | 3 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 3 feet long. Part #RC-173 | $3.95 In Stock | ||
Click on photo for larger view | 3 foot Extra Heavy-Duty Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Heavy duty thick cable, gold RCA connectors, excellent shielding properties, additional ground conductor provided. Part #RC-273 | $6.95 In stock | ||
Click on photo for larger view | 4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 4 feet long. Part #RC-174 | $4.95 In stock | ||
Click on photo for larger view | 4 foot Revisit™ right angle cables for Reverb Tanks. RCA at one end, stripped cable at opposite end. For connecting reverb tanks directly to a PC board via a soldered connection at the PC board end. Used by a number of manufacturers. Dual cable, excellent shielding properties, 4 feet long. Part #RC-374 | $4.95 In stock | ||
Click on photo for larger view | 5 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 5 feet long. Part #RC-175 | $5.95 In stock | ||
Click on photo for larger view | 6 foot Extra Heavy-Duty Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Heavy duty thick cable, gold RCA connectors, excellent shielding properties, additional ground conductor provided. Part #RC-276 | $9.95 In stock | ||
Switches | ||||
| FOOTSWITCH W/LED Sturdy metal construction, an aftermarket replacement from Revisit™. Works with the Crate VC3112 Vintage Club 30 and Crate VC5112 Vintage Club 50. Mono 1/4' Plug, 16 ft. cable. LED indicates condition of switch. Can be rewired internally to work with other amplifiers. Click here for wiring diagram. NOTE: Will not work with many amplifiers, even those that used LED's on the original footswitch, without rewiring. Electronics background suggested. Also - will generally NOT work with amplifiers which did not have an LED indicator on the original footswitch. Part #FBS-470L | $21.95 | ||
| DUAL FOOTSWITCH W/LED Sturdy metal construction, an aftermarket replacement footswitch from Revisit™. Works with the Crate BV120H Blue Voodoo 120 Head. Stereo 1/4' Plug, 16 ft. cable. LEDs indicate condition of switches. Can be rewired internally to work with other amplifiers. Click here for wiring diagram. NOTE: Will not work with many amplifiers, even those that used LED's on the original footswitch, without rewiring. Electronics background suggested. Also - will generally NOT work with amplifiers which did not have LED indicators on the original footswitch. Part #FBS-471L | $26.95 | ||
Click on photo for larger view | ORIGINAL Crate® PUSH SWITCH DPDT Mini Short-Throw Push Switch. Has 6 electrical terminals on bottom of switch (DPDT). Used for channel switching, level switching, FX switching, etc on the front panels of many Crate® amps from the 1990s to present. Found in the Palomino, BT50, and many other models. Original Crate® part number 88-302-02. Has actuator shaft of 2.7mm square. Part #88-302-02 | $4.95 | ||
Click on photo for larger view | ORIGINAL Ampeg® PUSH SWITCH DPDT Mini Short-Throw Push Switch. Has 12 electrical terminals on bottom of switch (2XDPDT). Used for pre-post switch on Ampeg SVT4-PRO. Original Ampeg® part number 88-303-02. Has actuator shaft of 3.3mm square. Part #88-303-02 | $9.95 | ||
Click on photo for larger view | ROCKER SWITCH, BLACK. Has 4 electrical terminals on back of switch (DPST). Non-lighted. 1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm) Part #SW-5072 | $3.95 | ||
Click on photo for larger view | ROCKER SWITCH, LIGHTED POWER, RED. Has 4 electrical terminals on back of switch.1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm). Internal neon lamp powered by either 125VAC or 250VAC. Used in some Crate model amps - but may not fit all. Verify the dimensions of the hole cutout in the panel before ordering. Also used on many Engl Amp models.Also replaces the # 700048-3159 power switch in most models of Furman power conditioners.ReplacesAmerican DJ part # Z-PDP/900-PS-Nfor use in the American DJ PC-100A PC-4 power centers. Part #SW-5075 | $4.95 | ||
Click on photo for larger view | ROCKER SWITCH, LIGHTED POWER, AMBER. Has 4 electrical terminals on back of switch.1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm). Internal neon lamp powered by either 125VAC or 250VAC. Used in some Crate model amps - but may not fit all. Verify the dimensions of the hole cutout in the panel before ordering. Also used on many Engl Amp models. Part #SW-5076 | $4.95 | ||
Click on photo for larger view | ROCKER SWITCH, LIGHTED POWER, GREEN. Has 4 electrical terminals on back of switch (DPST).1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm). Internal neon lamp powered by either 125VAC or 250VAC. Used in some Crate model amps - but may not fit all. Verify the dimensions of the hole cutout in the panel before ordering. Part #SW-5077 | $4.95 | ||
Click on photo for larger view | SWITCH, CARLING SPST TOGGLE, ORIGINAL REPLACEMENT FOR 60's and 70's Fender® AMPS (POWER & STANDBY SWITCHES) Part #SW-495 | $4.95 | ||
Click on photo for larger view | SWITCH, CARLING DPST PROGRESSIVE TOGGLE (OFF-STANDBY-PLAY) Replacement for amps which use a single toggle switch for both power and standby. Or, may be used to engineer a modification to amps which have a toggle power switch switch, but do not offer a standby switch (such as the Peavey Delta Blues, Fender® Blues Junior, etc). Seewiring information here. Part #SW-520 | $7.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - Rated at 20 Amps (125VAC) or 15 Amps (250VAC). Fits 1/2' chassis hole. Solder terminals or 1/4' push on, single pole / single throw (SPST). Two position - on/off. NOTE: RATED FOR AC SERVICE ONLY AT 250V MAX - DO NOT USE AS A GUITAR AMPLIFIER STANDBY SWITCH. Part #STS-20 | $3.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - MADE BY CARLING Rated At 15A/125VAC, 10A/250VAC. Two Position (on/off), Double Pole (DPST). Fits 1/2' Chassis Hole. Solder Terminals Or 1/4' Push-on. Fender® Part Number 0036570000. Part #SW-525 | $6.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - Made by Carling®- rated at 15A/125VAC, 10A/250VAC. Two position (on/off), single pole (SPST). Fits 1/2' chassis hole. Solder terminals. Part #SW-526 | $4.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - RATED AT 10 Amps (125VAC) or 10 Amps (250VAC) - TWO POSITION (ON/ON). Fits 1/2' chassis hole. Screw terminals, or remove screws for soldered connections. Double-pole double-throw, no center off - two positions (ON/ON). Part #STS-10-DPDT | $3.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - RATED AT 15 Amps (125VAC) or 10 Amps (250VAC) - TWO POSITION (ON/ON). Fits 1/2' chassis hole. Screw terminals, or remove screws for soldered connections. Double-pole double-throw, no center off - two positions (ON/ON). Part #STS-15-DPDT | $4.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - RATED AT 15 Amps (125VAC) or 10 Amps (250VAC) - THREE POSITION (ON/OFF/ON). Fits 1/2' chassis hole. Screw terminals, or remove screws for soldered connections. Double-pole double-throw, with center off - three positions (ON/OFF/ON). Part #STS-15-DPDT-CO | $5.95 | ||
Click on photo for larger view | FOOT SWITCH, CARLING BRAND, SPDT, LATCHING Found in many type of footswitches. Has 3 electrical terminals (single pole, double throw). Solder lugs for wire. Part #FS-492 | $9.95 | ||
Click on photo for larger view | FOOT SWITCH, CARLING BRAND, SPST, LATCHING, REPLACEMENT FOR Fender®, ETC. Carling SPST footswitch. Used in Marshall® etc. Reverb/tremolo/channel switching pedals.Has 2 electrical terminals (single pole, single throw). Solder lugs for wire. Part #FS-493 | $9.95 | ||
Click on photo for larger view | FOOT SWITCH, DPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS. Double-pole Double-Throw, made for direct connection to a PC board. Has 6 electrical terminals. Part #FS-498-PC (Also see our complete line of switches) | $3.95 |
Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. the replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. the distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.
Copyright ©2019 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
WARNING: these products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
![Ampeg Svt 15t Manual Treadmill Ampeg Svt 15t Manual Treadmill](/uploads/1/2/6/0/126060472/670176549.jpg)
HardwareJacksPotsKnobs |
Click on photo for larger view | Revisit™ VTL5C1 OPTO-ISOLATOR Replaces VTL5C1 from Vactec or Excelitas at an affordable price. Used in many Mesa-Boogie and Crate models in the channel switching circuit. 100dB dynamic range, fast response (2.5ms turn-on), very high dark resistance (50 M Ohm). Light resistance 200 Ohms at 20mA LED current. See datasheet here. Part #VTL5C1 | $4.95 | ||
| 10-Conductor Ribbon Cable 3' Used to interconnect circuit boards in a variety of amps. • 3 inches long • 10 conductors set at 0.1 inch spacing -complete cable is 1 inch wide • Bare wire termination for soldering to PC board at 0.1' hole spacing - no connectors • May be easily cut with an X-Acto knife to make a cable of fewer than 10 conductors. • Not recommended for use in the Fender Hot Rod Deluxe / Deville or Blues Deluxe / Deville. the ribbon cables used in those amps have ribbon cables with conductors set at 0.156' spacing - this cable is too narrow for that application. Part #RJ-310 | $0.99 | ||
Ampeg® & Crate Hardware | ||||
Click on photo for larger view | L-PAD FACE PLATE AND KNOB, for 3/8' diameter threaded bushing found on most L-Pad Level controls. Face plate AND knob only! L-Pad ordered separately. Fits many bass cabinets including the SWR Goliath, Marcus Miller Golight 410, Workingman 8x10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF, SVT-810SPC, BXT210M, BXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, theEngl B115 as well as many others. This is the face plate and knob only - L-PAD itself ordered separately. Raised lettering in charcoal gray instead of white. 3 1/8 inches in diameter, 7/8 inch depth into cabinet. Requires 2 inch diameter hole for mounting. Screws not included. Part #LFP-380 | $3.99 | ||
8 Ohms Click on photo for larger view | L-PAD, 8 Ohms, 3/8' threaded bushing (3/8' long), with plate, knob and hardware. May also be used with the LFP-380 face plate and knob. 8 ohms - for use with 8 ohm speakers, horn drivers or tweeters. L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads, features a 3/8' shaft length, and comes with mounting hardware. This style of L-Pad is found on many popular bass cabinets to control the horn/tweeter level. 2.5 inches in diameter, 1 inch thick. Included face plate is 2 1/8' x 2 1/8'. Part #LPD-262 | $17.95 | ||
16 Ohms Click on photo for larger view | L-PAD, 16 Ohms, 3/8' threaded bushing (3/8' long), with plate, knob and hardware. May also be used with the LFP-380 face plate and knob. 16 ohms - for use with 8 ohm speakers, horn drivers or tweeters. L-pads adjust the relative volume of drivers connected to them by placing added resistance in series and parallel, keeping impedance a constant 8 ohm load. This L-pad is rated at 100 watts RMS, is designed to be used with 16 ohm loads, features a 3/8' shaft length, and comes with mounting hardware. This style of L-Pad is found on many popular bass cabinets to control the horn/tweeter level. 2.5 inches in diameter, 1 inch thick. Included face plate is 2 1/8' x 2 1/8'. Part #LPD-261 | $17.95 | ||
Click on photo for larger view | Ampeg® 'a' Logo Used on modern Ampeg Speaker Cabinets, this 3 inch x 4 inch plastic logo is affordably priced. Mounting screws included. Mounting centers are2 ¼' x 2 ⅜'. Part #AL-921 | $4.95 | ||
Click on photo for larger view | Black Logo Mounting Screws Set of 4 logo mounting screws. these are #5 x 7/16' black oxide screws, set of 4. Fit the AL-921 Ampeg logo, and the Fender FAL-912 logo. Part #LS-504 | $0.99 (for a set of 4 screws) | ||
Click on photo for larger view | TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34. Used in many different amplifier brands. 1 1/2' Mounting Centers. Part #TC-142 | $1.79 | ||
Click on photo for larger view | LARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES. Part #TC-143 | $2.89 | ||
Click on photo for larger view | TUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALL. Includes new base, if needed. Spring in top of shield which fits over the tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Ampeg, Crate and many other brands. Holes in base spaced 1 1/8' apart. Shield and base only - socket not included. Part #TS-325S | $1.69 | ||
Click on photo for larger view | TUBE SHIELD, BAYONET 'PUSH AND TWIST' TYPE, ALUMINUM, 1 15/16' TALL, SET OF 6. Includes new bases, if needed. Spring in top of shield fits over the tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Ampeg, Crate, and many other brands. Holes in base spaced 1 1/8' apart. Shield and base only - socket not included. Part #TS-325S-6 | $8.95 | ||
(TUBE NOT INCLUDED) Click on photo for larger view | Revisit™ PRE-AMP TUBE DAMPER RINGS. Use two (or three) of these rings around a pre-amp tube to reduce noise and microphonics. An economical alternative to more expensive tube dampers. Will withstand high temperatures of pre-amp tubes, reusable when you change tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes.these dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. Part #PTD-6 | $2.99 (Set of 6 rings) | ||
Click on photo for larger view | Ground Connection Terminals - Flat Made from tin-plated brass - will not rust. Used to connect a ground wire to a screw and nut on a chassis. Flat, with one hole for wire. With built-in lock washer to keep the screw and nut from loosening. Designed for a #8 size screw. Pack of 10 terminals. Part #2310915 | $2.99 (Pack of 10 terminals) | ||
Click on photo for larger view | TERMINAL STRIPS, 6 LUG, SET OF 2. Perfect for amplifier circuit additions or modifications. End terminals on each strip are the mounting lugs, so they become a ground lug if attached to a metal chassis. Each terminal strip is 2 1/4 inches long. the lugs are set on 3/8 inch centers. Each lug will accept wires up to 16ga - smaller gauge allows multiple wires to be connected to each lug. Set contains 2 terminal strips as pictured. Mounting hardware not included. Part #2320822 | $2.89 (for a set of 2 terminal strips) | ||
Click on photo for larger view | CUP WASHER, BLACK METAL, PACK OF 10. USED WITH #8 BLACK SCREW ON AMP AND SPEAKER CABINETS. Part #BCW-10 | $1.29 (pack of 10) | ||
Click on photo for larger view | SPEAKER BAFFLE MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Locking nut and washer included. Phillips head. Drill hole, insert and tighten screws into wood from front of baffle. Install grill cloth, and you have professional speaker mounting studs. Set of 4. Part #SC-409-4 | $2.29 (For a pack of 4 screws with nuts and lock washers) | ||
Click on photo for larger view | ISOLATION WASHER - 3/8' 3/8' outside diameter neoprene bonded flat washer. Perfect for bolting speakers to cabinets. It will securely hold the speaker in place and stop any rattling. For use with #6 and #8 screws. Set of 4 washers. Part #SIW-38-4 | $0.59 (For a set of 4 washers) | ||
Click on photo for larger view | BLACK PAN-HEAD WOOD SCREWS, #6 X 3/4', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #6 screw, 3/4 inch long, pack of 10. Part #SCR-435 | $0.79 (pack of 10) | ||
BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 1/2 inch long, pack of 10. Part #BWS8-5 | $0.89 (pack of 10) | |||
BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 3/4 inch long, pack of 10. Part #BWS8-75 | $0.95 (pack of 10) | |||
BLACK PAN-HEAD WOOD SCREWS, #8 X 1', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 1 inch long, pack of 10. Part #BWS8-1 | $1.05 (pack of 10) | |||
BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2', PACK OF 10. Deep threads, sharp point, pan head with Philips drive. #8 screw, 1-1/2 inches long, pack of 10. Part #BWS8-15 | $1.19 (pack of 10) | |||
Click on photo for larger view | CAGE NUT, ZINC, 10-32 THREAD. Used on square-punched amp chassis rails to secure the chassis to the cabinet. Frequently found in Peavey, Crate, Ampeg, other brands. NOT used in Marshall® - see the MCN-4. Works with all 10-32 screws. Verify screw thread before ordering, as not all cage nuts are 10-32. Zinc coating retards oxidation. Pack of 4 nuts. Made in Canada by Hammond Industries. Part CNA-1421 | $4.29 (pack of 4) | ||
Click on photo for larger view | SMALL BLACK RUBBER FEET, PACK OF 4. 3/4' DIAMETER AT TOP, 5/8' DIAMETER AT BOTTOM, 5/16' TALL. BLACK RUBBER WITH METAL INSERT. USED TO SUPPORT EFFECTS, SMALLER AMPS, SMALLER MIXERS. SCREWS NOT INCLUDED. Part #BRF-4 | $2.95 (pack of 4) | ||
Click on photo for larger view | SMALL BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for smaller amps, amp heads, or speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. Just under 1 inch - 15/16' diameter at the top, rounded down to 5/8' diameter at the bottom, and 3/8' tall. Screws not included. Set of 4 feet. Part #BRF-723 | $3.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for large rack cabinets or speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter x 1' tall. Mounting screws not included. Part #BRF-1691 | $4.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for rack-mount amps, combo amps, or small speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter (wide end) x 3/4' diameter (narrow end) x 0.85' tall. Mounting screws not included. Set of 4 feet. Part #BRF-9105 | $4.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 4. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter x 5/8' tall. Mounting screws not included. Part #BRF-1692 | $4.95 (pack of 4) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 5. This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets. the integral metal washer in the mounting hole helps prevent mounting screw 'break-through' and adds overall durability. 1' diameter x 5/8' tall. Mounting screws not included. This set of 5 works well for the main feet used on the Ampeg BA-210 when the cabinet is in the upright position. Part #BRF-1692-5 | $6.25 (pack of 5) | ||
Click on photo for larger view | MEDIUM BLACK RUBBER FEET, SET OF 4. Tapered: 1 3/16' Diameter At Small End, 1 1/4' Diameter At Large End. 1/2' Tall. Black Rubber With Metal Insert. Used To Support Effects, Amps, Mixers. Mounting Screws Not Included. Part #BRF-9112 | $4.95 (pack of 4) | ||
Click on photo for larger view | X-LARGE BLACK RUBBER FEET, SET OF 4. Tapered - 1 5/8' Diameter At Large End, 1 1/4' At Small End. 3/4' Tall. Black Rubber With Metal Insert. Used To Support Amp Heads, Speaker Cabinets. Mounting Screws Not Included. Part #BRF-9107 | $7.95 (pack of 4) | ||
Click on photo for larger view | Fender® Style Flat Mount 2' Caster Wheels - Set of 4. Great for Fender® and many other brands of amps or cabinets. Each wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2' in diameter. Specifications found here. Note: Mounting screws NOT included. Part #FCW-4F | $24.95 (Set of 4 casters) NOT SOLD OUTSIDE the USA | ||
Click on photo for larger view | Fender® Style Pop-Out 2' Caster Wheels - Set of 4. Great for Fender® and many other brands of amps or cabinets. Each wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2' in diameter. the same type of removable caster wheels used on Fender® amps since the 1960s. Note: Mounting screws NOT included. Must drill 5/8' hole in bottom of cabinet to accomodate post for wheel. Part #FCW-4R | $28.95 (Set of 4 pop-out casters) NOT SOLD OUTSIDE the USA | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, BLACK WITH BLACK STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8-9/16 inches (8.57'), center-to-center mounting distance is 7-3/8 inches (7.38') Black with black stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-281 | $12.95 | ||
'SHORTY' AMP HANDLE Click on photo for larger view | Revisit™ 'SHORTY' AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, BLACK WITH BLACK STITCHING Similar to the AH-281 handle above, but 1-3/4 inches shorter. Handle length is 6-13/16 inches (6.80'), center-to-center mounting distance is 6 inches (5.98') Black with black stitching, nickel mounts. Mounting screws not included - use SC-402 screw pack. This is a great handle to consider for smaller combo amps, practice amps, etc. Delivers a professional quality look and reliability in a smaller size for smaller amps. More details Part #AH-281-S 'Shorty' | $8.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, DARK BROWN WITH BROWN STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Dark brown with brown stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-270 | $12.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, TAN WITH TAN STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Tan with tan stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-108 | $12.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, DARK BROWN WITH WHITE STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Dark brown with white stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-318 | $12.95 | ||
Click on photo for larger view | Revisit™ AMP HANDLE, VINTAGE LEAtheR-LOOK STYLE, DEEP NAVY BLUE-GREY WITH WHITE STITCHING Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera, Blackstar, many others. Handle length is 8 9/16 inches (8.57'), center-to-center mounting distance is 7 3/8 inches (7.38') Dark navy blue-grey with white stitching, nickel mounts. More details Mounting screws not included - use SC-402 screw pack. Part #AH-319 | $12.95 | ||
Click on photo for larger view | Fender® or Ampeg® VINTAGE STYLE GUITAR AMP HANDLE, RAISED, BLACK STITCHED SIMULATED LEAtheR.Black handle strap, made of simulated leather, replacement for Fender® 'tweed' style amps or vintage Ampeg amps (as well as other vintage amps. Has slight 'raised' bump near the center of the handle. Black, white stitched. 6-1/4 to 6-1/2 inches between mounting posts. Total length 8-3/4'. Mounts and screws are included. Part #GAH-782 | $15.95 | ||
Click on photo for larger view | Revisit™ BLACK GUITAR AMP HANDLE, WITH HARDWARE. Rugged rubber black handle strap, steel reinforced. Black metal caps. Black 10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8'wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is 10 1/4'. Part #GAH-271B | $7.99 | ||
Click on photo for larger view | Revisit™ GUITAR AMP HANDLE - BLACK. Rugged rubber black handle strap, steel reinforced. Black metal caps. Screws not included - recommend using our SC-403B 10-32 type screws along with a 10-32 T-Nut for secure mounting. Handle strap is 7/8' wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is 10 1/4'. Part #GAH-1 | $6.99 | ||
| BLACK HANDLE SCREWS Pack of 2 stainless-steel handle screws finished in satin black for use with black end-cap handles, such as our GAH-1, OAH-456, or GAH-271B. 1' Long, 10-32 threads, finished in satin black to match black end caps. Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4' or less. Will not work with external nut - must be a T-Nut. Will not work with cabinet wood thicker than 3/4'. See Data Sheet here Part #SC-403B | $0.99 (for a pack of 2 screws) | ||
Click on photo for larger view | Revisit™ CHROME/BLACK GUITAR AMP HANDLE - CHROME, WITH HARDWARE. Rugged rubber black handle strap, steel reinforced. Chrome metal caps. 10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8'wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is 10 1/4'. Not recommended for Fender, as the screws are set too far apart for Fender® amp specifications. Part #GAH-271C | $7.99 | ||
| HANDLE SCREWS Pack of 2 stainless steel handle screws for GAH-271C Handle. 1' Long, 10-32 threads. Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4' or less. Will not work with external nut - must be a T-Nut. Will not work with cabinet wood thicker than 3/4'. See Data Sheet here Part #SC-403 | $0.99 (for a pack of 2 screws) | ||
Click on photo for larger view | LARGE SIZED STRAIN RELIEF FOR 35/64' X 5/8' HOLE Popular strain relief found on most vintage guitar amplifiers with round power cords. Designed for 5/16' cord diameter. Click here for specific dimensions of chassis hole. For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below. Part #SR-1200 | $0.99 | ||
Click on photo for larger view | STRAIN RELIEF INSTALLATION/REMOVAL TOOL Removing and installing strain reliefs can be a frustrating job. Standard pliers just do not get the job done and can damage the strain relief. these special strain relief pliers are just what you need. they fit perfectly on AC power cord strain reliefs and give you the leverage you need to compress the strain relief for easy removal and installation, without damage. Part #YTH-205 | $12.95 | ||
Click on photo for larger view | EXTRA-LARGE SIZED STRAIN RELIEF FOR 3/4' X 27/32' HOLE Popular strain relief found on a few larger vintage bass amplifiers and power amplifiers with very thick power cords. Designed for 11/32' cord diameter. Click here for specific dimensions of chassis hole. Part #SR-1300 | $0.99 | ||
Click on photo for larger view | SMALL RUBBER CHASSIS GROMMET FOR 3/8 INCH CHASSIS HOLE (GROMMET INNER HOLE 1/4 INCH) Chassis grommet, for electrical insulation, wire protection and management, shock absorption, or mechanical isolation. This grommet has a 1/4 inch diameter inner hole, and mounts in a 3/8 inch chassis hole. Full datasheet here. Part #RCG-739 | $0.49 each | ||
Click on photo for larger view | LARGE RUBBER CHASSIS GROMMET FOR 1/2' CHASSIS HOLE (GROMMET INNER HOLE 3/8 INCH) Chassis grommet, for electrical insulation, wire protection and management, shock absorption, or mechanical isolation. This grommet has a 3/8 inch diameter inner hole, and mounts in a 1/2 inch chassis hole. Full datasheet here. Part #RCG-745 | $0.49 each | ||
Ampeg Fans | ||||
Click on photo for larger view | thermoCool Fan. 80 x 38mm Sleeve Bearing 19 CFM. thermocool axial fans provide enhanced cooling for a variety of electronic devices. Leading air flow technology is designed into every thermocool product resulting in reduced turbulence, low noise levels and a more energy efficient product. thermocool fans are ideal for use in computer systems, portable CD and DVD players, stereo components, overhead projectors, laptop computers, and many other electronic applications where circulation is a key concern. This fan is the replacement for the fan used in the Ampeg SVT Classic, Ampeg® part number 24-321-03. Specifications: • Power: 120V AC, 60 Hz • Sleeve bearing • Lead wire connection • 0.13 amps • 2400 RPM • 28dB noise level • 23 CFM air flow • Dimensions: 80 mm (H) x 80 mm (W) x 38 mm (D) [3 1/4' (H) x 3 1/4' (W) x 1 1/2' (D)] For use on 110-120VAC System only, as found in North America. Part #G8038HAS | $19.95 | ||
Ampeg® & Crate® Jacks | ||||
Click on photo for larger view | JACK, 1/4', CHROME NUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-SLEEVE, 4 PINS. Generally found only in Crate or Ampeg products.Common input, footswitch or effects loop jack exclusive to Crate® and Ampeg®. (Other brands with chrome-nut jacks use a straight pin jack such as the J-580.) 4 pins, PC mount, with chrome nut and washer. Note 'L-Leg' pins as shown in photo. Original Crate or Ampeg part number 39-119-01. Part #J-580L | $3.95 | ||
Click on photo for larger view | JACK, 1/4', CHROME NUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE, L-LEG, TIP-SLEEVE, 4 PINS, GOLD CONTACTS. Generally found only in Crate or Ampeg products.Common input, footswitch or effects loop jack exclusive to Crate® and Ampeg®. (Other brands with chrome-nut jacks use a straight pin jack such as the J-580.) 4 pins, PC mount, with chrome nut and washer. Gold contacts for improved conductivity, performance, and reliability. Note 'L-Leg' pins as shown in photo. Part #J-580LG | $4.95 | ||
Click on photo for larger view | JACK, 1/4', CHROME NUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF UK, L-LEG, TIP-RING-SLEEVE, 6 PINS. Generally found only in Crate or Ampeg products.Common input, footswitch or effects loop jack exclusive to Crate®, Ampeg®. (Other brands with chrome-nut jacks use a straight pin jack such as the J-581.) 6 pins, PC mount, with chrome nut and washer. Note 'L-Leg' pins as shown in photo. Original Crate or Ampeg part number 39-120-01. Part #J-581L | $4.50 | ||
Click on photo for larger view | JACK, 1/4', INPUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-SLEEVE, 4 PINSCommon input jack in Crate®, Ampeg®, others. Ampeg and Crate® part number 39-116-01. 4 pins, PC mount, with nut and washer. Note 'L-Leg' pins as shown in photo. Part #J-503L | $3.79 | ||
Click on photo for larger view | JACK, 1/4', INPUT, CLOSED CIRCUIT, PC MOUNT, L-LEG, TIP-RING-SLEEVE, 6 PINCommon input jack in Crate®, Ampeg®, others. Ampeg and Crate part number 39-117-01. 6 pins, PC mount, with nut and washer. Note 'L-Leg' pins as shown in photo. Part #J-504L | $3.95 | ||
Click on photo for larger view | JACK NUT, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall® AND OtheRS. Note: Replaces most black plastic jack nuts EXCEPT for Roland. Will NOT fit Roland jacks. Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks. Also fits the J-518 and J-519 jacks. Part #J-5NT | $0.50 | ||
Click on photo for larger view | JACK NUT MULTI-PACK - SAVE! 6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall® AND OtheRS. Note: Replaces most black plastic jack nuts EXCEPT for Roland. Will NOT fit Roland jacks. Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks. Also fits the J-518 and J-519 jacks. Part #J-5NT-6 | $2.39 | ||
Click on photo for larger view | JACK NUT/FERULE, CHROME, with BLACK PLASTIC BEZEL/WASHER - GENUINE CLIFF UK Replacement nut and bezel washer for the J-501, J-501S, J-580, J-581, J-580L and J-581L jacks. Note: the threads on this nut are coarse (3/8-20), and are for genuine Cliff jacks. Note: there are some generic jacks on the market with finer thread nuts. This nut will not fit those jacks. This nut is for genuine Cliff UK jacks. Bezel is included with this nut. Part #JN-200W | $0.79 | ||
Click on photo for larger view | JACK NUT/FERULE, BLACK, with INTEGRAL BLACK PLASTIC BEZEL - GENUINE CLIFF UK Replacement nut and bezel washer which will fit the J-501, J-501S, J-580, J-581, J-580L, J-580LG, and J-581L jacks. Note: the threads on this nut are coarse (3/8-20), and are for genuine Cliff jacks. Note: there are some generic jacks on the market with finer thread nuts. This nut will not fit those jacks. This nut is for genuine Cliff UK jacks. Bezel is integral to the nut and cannot be removed. This is the jack nut used on the Marshall JMP-1 Preamp, and on some versions of the Marshall DRP-1 Direct Recording Preamp. Part #JN-864 | $0.79 | ||
Click on photo for larger view
| JACK, 1/4', PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED. Both tip and ring conductors are switched (normally closed). Used in Crate® and other brands. NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW. Part #J-527 | $4.50 | ||
JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 | $0.89 (Set of 1 washer and 1 nut) | |||
| Dual Chassis-Mount Banana Binding Posts. Used on the rear panel of many power amplifiers and some bass amps, such as the Ampeg B4R. Red and black posts, accepts either single or dual banana plugs. Mounts in two 1/2' holes on 3/4' centers, panel thickness up to 1/4'. 15A rating, gold plated contacts. | $4.99 | ||
Click on photo for larger view | JACK, 1/4', MONO, OPEN CIRCUIT, WIRED, Switchcraft® Found in many guitars, effects pedals, amps speaker output. Includes nut and washer. Part #J-11 | $2.25 | ||
Click on photo for larger view | JACK, 1/4', MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft® Found in vintage amps as the input jack. Includes nut and washer. Part #J-12A | $2.79 | ||
Click on photo for larger view | JACK, 1/4', TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft® Used with T/R/S plugs for either balanced connections or stereo connections. Also very common in guitars with active pickups, and as the input jack on some effects pedals. the ring conductor is used in these cases to 'turn on' the battery by tying one leg of the battery to ground via the plug. Part #J-12B | $2.99 | ||
Click on photo for larger view | JACK, 1/4', TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING Same as the J-12B jack, but with longer (3/8') threaded bushing for mounting in thicker panels. Includes nut and washer. Part #J-L12B | $3.99 | ||
Click on photo for larger view | JACK, 1/4', TIP/RING/SLEEVE, WITH TIP SHUNT. Switchcraft 13B Jack. Tip/Ring/Sleeve Switchcraft jack. Tip has a shunt contact, ring contact is open circuit. Part #J-13B | $6.95 | ||
Click on photo for larger view | JACK, 1/4', MONO, CLOSED CIRCUIT, RIGHT ANGLE PC MOUNT, Switchcraft® STYLE, NYLON THREADS, 3 PINS Common input jack in Crate® & Ampeg®, and in some solid state products from Fender® during the early 1980s. Nut and washer included. Part #RN112APC | $5.79 | ||
Click on photo for larger view | JACK, 1/4', STEREO, CLOSED CIRCUIT, RIGHT ANGLE PC MOUNT, Switchcraft®STYLE, NYLON THREADS, 5 PINS Common input jack in Crate® & Ampeg® products. Nut andwasher included. Switchcraft RN114BPC. Nut and washer included. Part #J-114PC | $5.99 | ||
Click on photo for larger view | SAVE WITH MULTIPACK! JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6 Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Set of 6 washers and 6 nuts. Part #JNUT-38-6 | $4.50 (Set of 6 washers and 6 nuts) | ||
JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 | $0.89 (Set of 1 washer and 1 nut) | |||
| JACK, 1/4', TIP/RING/SLEEVE, 7 PIN, PC MOUNT, Fender®, Hartke® and Crate® Amps. Fender®, Hartke® or Crate® PCB mount 1/4' jack. 7 pins. Fits several Hartke® amp models 1990 - present, and several Crate® models, especially in the GX series. Used in the Fender® SKX65R and SKX100R for the input jacks. Used in some Fender® Squier and Sidekick amps as the headphone jack. Hartke® part number 350023 and 300519. Fender® part number 022923. NUT & WASHER NOT INCLUDED - ORDER JN-916. | $6.95 | ||
NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE. | $0.39 | |||
SAVE WITH MULTIPACK! NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE, SET OF 6. | $2.09 | |||
Click on photo for larger view | JACK, 1/4', Peavey® PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING. Both tip and ring conductors are switched (normally closed). 5 pins. Original Peavey® part number 31466217. Used in Peavey®, Mackie, Fender, Crate, Ampeg and other brands. Replaces Switchcraft 114BPCX and 114BPCSX. Nut and washer on this jack ARE included. Part #J-529 | $2.99 | ||
Click on photo for larger view
| JACK, 1/4', PC MOUNT, STEREO, 4 PINS, SWITCHED, METAL BUSHING. Tip is switched (normally closed), ring conductor is not switched. Made by Neutrik/Rean. Used in a variety of brands. Replaces Switchcraft. NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW. Part #J-524A | $3.50 | ||
Click on photo for larger view | SAVE WITH MULTIPACK! JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6 Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Set of 6 washers and 6 nuts. Part #JNUT-38-6 | $4.50 (Set of 6 washers and 6 nuts) | ||
JACK NUT AND WASHER, METAL, SWITCHCRAFT® Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8' bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4' jacks. Does NOT fit the 24mm Marshall® pots. Part #JNUT-38 | $0.89 (Set of 1 washer and 1 nut) | |||
Click on photo for larger view. Jack is in the picture to demonstrate how the washers are installed - jack is NOT included with the washers. | INSULATING SHOULDER WASHER, FIBER Pair of fiber insulating shoulder washers for Switchcraft jacks with metal bushings. Used to mount standard jacks in a 1/2' diameter chassis hole, while insulating the metal bushing (ground) of the jack from the chassis. ID 3/8', OD 1/2'. Works great when replacing isolated plastic jacks with a more durable metal jack, which is frequently done on the input jacks of the Fender® Hot Rod Deville/Deluxe and Blues Deville/Deluxe. Two washers are used on each jack, and the 'shoulders' are placed facing each other through the chassis. the washers not only isolate the ground of the jack electrically for noise reduction, but also stabilize the jack in the 1/2' diameter hole. Jack shown in picture NOT included. Works well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13, J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks. Part #ISW-3069 | $0.49 (For a pair of washers. Each jack needs two washers.) | ||
Click on photo for larger view | JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR PC BOARD (SOLDER PINS). Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including Ampeg®. Part #J-NL4MD-V | $4.95 | ||
Click on photo for larger view | JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR WIRE ATTACHMENT (3/16' PUSH ON CONNECTORS OR SOLDER TABS). Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including Ampeg®. Part #J-NL4MP-2 | $4.95 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for speaker cabinets with one speaker. Includes Switchcraft #11 jack, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. For two-speaker cabinets, see the SCH-2411X2, below. Part #SCH-2411 | $10.49 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE FOR TWO SPEAKER CABINET. Preassembled for speaker cabinets with two speakers in parallel. Includes Switchcraft #11 jack, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors, plus an additional 24' jumper cable. Part #SCH-2411X2 | $14.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH 1/4' STRAIGHT PLUG and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for combo amps with one speaker. Includes 1/4' straight plug, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. For 2-speaker cabinets, add the SJ-150 jumper, below. Part #SCH-224 | $10.49 | ||
Click on photo for larger view | Revisit™ SPEAKER JUMPER CABLE polyvinyl insulated silver plated copper speaker wire, 18 gauge, twisted pair, black and white. Terminated at each end in standard 3/16' speaker fast-on connectors. Great for connecting speakers in parallel in 2x12 or 4x12 cabinets. 24 inches (61 cm) long. Made in USA. Part #SJ-150 | $5.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS COMPLETE WITH 1/4' RIGHT-ANGLE PLUG and 24' SPEAKER WIRE FOR SINGLE SPEAKER. Preassembled for combo amps with one speaker. Includes 1/4' straight plug, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. For 2-speaker cabinets, add the SJ-150 jumper, above. Part #SCH-287 | $10.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS, 2 ft LONG, RIGHT-ANGLE PLUG TO BARE TINNED WIRE, 16 GAUGE CABLE Replacement right-angle plug with 24' cable and stripped, tinned bare wire. Used to replace speaker cable in many combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4' jack and plug. Heavy-duty 16ga round black speaker cable, right-angle plug and bare wire ready for soldering to one speaker. Part #SCH-7090 | $4.99 | ||
Click on photo for larger view | Revisit™ SPEAKER HARNESS Replacement right-angle plug with 34' cable and 3/16' fast-on connectors. Used to replace speaker cable in most combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4' jack and plug. 18ga black zip cord, right-angle plug and fast-on connectors for attachment to one speaker. Part #SCH-280 | $6.50 | ||
Click on photo for larger view | Revisit™ SPEAKER CABLE - HEAD TO CABINET - 4 FEET LONG Black 4 feet 16 gauge speaker cable, with one straight 1/4 inch plug and one right-angle 1/4 inch plug. Used to connect amplifier head to cabinet. Part #SCH-7028 | $4.99 | ||
Click on photo for larger view | JACK PLATE, BLACK METAL, SINGLE 1/4' JACK, 2' OUTSIDE DIAMETER. Similar in style to vintage Fender® jack plates. Works well with the Switchcraft J-11 1/4' jacks that we carry. Hole is 3/8', for most Switchcraft type jacks. Easy to install, economical. Includes 3 black oxide coarse-thread mounting screws, #6x3/4'. Jack not included - order separately. For size specifications, click here. Part #JP-180 | $1.49 | ||
Click on photo for larger view | Revisit™ JACK PLATE COMPLETE WITH SWITCHCRAFT #11 JACK. Switchcraft #11 jack preinstalled with lock washer and trim washer. Outside diameter 2 inches (51mm). Designed to fit flush against a 1 1/8' (29mm) cabinet hole. Easy to install - drill 1 1/8' hole in cabinet, attach speaker wiring to jack and speaker, attach plate to cabinet. Part #JPC-180 | $4.95 | ||
Click on photo for larger view | Revisit™ JACK PLATE COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE. Preassembled - includes 2' diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. Outside jack plate diameter 2 inches (51mm). Designed to fit flush against a 1 1/8' (29mm) cabinet hole. Easy to install - drill 1 1/8' hole in cabinet, attach speaker wiring to speaker, attach plate to cabinet. For two-speaker cabinets, see the JPH-182, below. Part #JPH-180 | $11.95 | ||
Click on photo for larger view | Revisit™ JACK PLATE COMPLETE WITH GENUINE SWITCHCRAFT #11 JACK and 24' SPEAKER WIRE, PLUS ADDITIONAL 24' JUMPER. Preassembled - includes 2' diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer, and 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors. Outside jack plate diameter 2 inches (51mm). Designed to fit flush against a 1 1/8' (29mm) cabinet hole. Includes a second 24 inch polyvinyl-insulated 18 ga speaker wire terminated in 3/16' push-on speaker connectors to connect to a second speaker in the same cabinet. Easy to install - drill 1 1/8' hole in cabinet, attach speaker wiring to speakers, attach plate to cabinet. Part #JPH-182 | $15.95 | ||
Click on photos for larger views | JACK PLATE, MONO/STEREO, PLUG AND PLAY This unit eliminates the confusing switch found on most stereo cabinets. Just pick your impedance and plug in. Labels shows the common 4 or 16 Ohm Mono and 8 Ohm Stereo option. Ready to install with a steel dish, wires, and speaker connectors already assembled - as shown in the photo. Requires a 3 inch x 3-7/16 inch rectangular hole cut in the cabinet. Direct easy replacement for many existing small jack dishes. No soldering required. Complete wiring directions included - click here for more details. Designed to be used with 2x12 cabinets containing two 8-ohm speakers, 4x12 cabinets with four 16-ohm speakers, or 4x12 cabinets with four 4-ohm speakers. Can be used for the following configurations:
Part #CJP-1 | $25.95 | ||
Ampeg Knobs | ||||
Click on photo for larger view | KNOB, Ampeg®, Classic Genuine Ampeg® amp knob, black with white pointer. Fits pots with 1/4' D-shaft type shafts. Part #K-324 | $5.95 | ||
Ampeg Relay | ||||
Click on photo for larger view | RELAY, Ampeg®, SVT-4PRO and other models Protection relay used in the SVT-4PRO. Common failure item - contacts become oxidized or burned and fail to connect the speakers to the power amp, even when the relay clicks in. there are two of these relays in the SVT-4 PRO, at locations K-101 and K-201. Original Ampeg part number 82-090-01 Part #82-090-01 | $18.95 | ||
Crate® Pots | ||||
Crate Amplifiers is no longer in business as of 2018, and potentiometers for their amps are no longer available. | ||||
Ampeg® & Crate® AC Power | ||||
Click on photo for larger view | IEC POWER CONNECTOR, AMPEG®, NON-FUSED, PCB MOUNT Used in the Ampeg® SVT-3-PRO, SVT-4-PRO, SVT-5-PRO, SVT-6-PRO, B2R, B4R, B5R bass amplifiers. Original Ampeg® part number 17-604-01. Datasheet here. Part #17-604-01 | $4.95 | ||
Click on photo for larger view | Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END. COMMON REPLACEMENT CORD FOR MANY GUITAR AMPS, POWER AMPS, EFFECTS UNITS, ETC.Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. IEC connector at equipment end. Used only in North America. Part #PC-300 | $5.95 | ||
Click on photo for larger view | Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END. Replacement Cord For Many Guitar Amps, Power Amps, Effects Units, Etc. 10 Ft Length Give Extra Flexibility In Equipment Placement, Reduces Use Of Extension Cords. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. IEC connector at equipment end. Used only in North America. Part #PC-600 | $10.95 | ||
Click on photo for larger view | SUPER-LONG Revisit™ 4 METER (about 13 ft) POWER CORD, 3-WIRE, 18ga, SVT type, 'Thin Line'. OUR LONGEST POWER CORD! Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length is a super-long 13 feet, cord thickness is 0.24 inches (about 1/4' or 6.2mm). Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SVT13-TL | $14.95 | ||
Click on photo for larger view | EXTRA-LONG Revisit™ 12 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length is an extra-long 12 feet, cord thickness is 0.29 inches(about 9/32' or 7.3mm). This cord is of appropriate gauge and physical thickness for application in most medium to large guitar amps with 'hard-wired' power cords. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SJT12 | $13.95 | ||
16 gauge: Click on photo for larger view | LONG 10 ft POWER CORD, 3-WIRE, 16ga, SJT type. Cut end for installing (soldered connection) into many vintage large power amps or large bass amps using a 3-wire cord. This 16 gauge cord is not normally used on guitar amps, as they do not require the heavy 16 gauge. Cord length is 10 feet, cord thickness is 0.32 inches (about 5.6' or 8.1mm), wire gauge is 16ga. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-163SJT10 | $12.95 | ||
18 gauge: Click on photo for larger view | LONG 10 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut end for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length is 10 feet, cord thickness is 0.29 inches (about 9/32' or 7.3mm). This cord is of appropriate gauge and physical thickness for application in most medium to large guitar amps with 'hard-wired' power cords (Fender, for example). Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SJT10 | $11.95 | ||
Click on photo for larger view | Revisit™ 8 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length 8 feet, cord thickness is 0.29 inches (7.3mm). Part #PC-183SJT8 | $9.95 | ||
Click on photo for larger view | 8 ft POWER CORD, 3-WIRE, 18ga, SVT type, 'Thin Line'. Cut ends for installing (soldered connection) into many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older amps). Cord length 8 feet, 18 gauge, cord thickness is 0.24 inches (about 1/4' or 6.1mm). Thinner than the PC-183SJT8 cord, this cord is better suited for replacing amp cords in smaller amplifiers where there was formerly a 2-wire cord without ground. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in North America. Part #PC-183SVT8-TL | $9.95 | ||
Click on photo for larger view | Fender® style reverb or AC cable clamp. Used on Fender amps since the early 60s to hold the reverb cable to the side of the cabinet. Clamp is 3/8' diameter, comes with 3/4' screw for mounting. Also used in some amplifiers to hold the AC cord to the cabinet wall. Fender® part number 022941. Works on many other brands of amplifiers as well. Part #RCC-381 | $0.99 | ||
Ampeg® & Crate® Reverb Tanks | ||||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 3 spring, equivalent to Accutronics 9AB2C1B. Input impedance 10 ohms, output impedance 2575 ohms, medium decay (1.75 - 3 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Hughes & Kettner®, MarshallTM, Ampeg, Crate, Fender®, Mesa Boogie, Guytron, Rocktron, DOD, Summit Audio, and Smokey. See explanation of Accutronics reverb tank numbering systemhere. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #9AB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $38.99 In stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 3 spring, equivalent to Accutronics 9EB2C1B. Input impedance 800 ohms, output impedance 2575 ohms, medium decay (1.75-3.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Hughes & Kettner®, MarshallTM, Ampeg, Crate, Fender®, Mesa Boogie, Guytron, Rocktron, DOD, Summit Audio, and Smokey. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #9EB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $38.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4AB3A1B. Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input grounded/output grounded, designed for horizontal mounting, open side down. Replacement for the Gibbs Type F reverb tanks used in the 60's and early 70's, including Ampeg models Echo Jet, Echo Twin, B12X, B12XY. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty detailshere. Part #4AB3A1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4AB3C1B. Input impedance 10 ohms, output impedance 2575 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Hughes & Kettner®, MarshallTM, Ampeg, Crate, Fender®, Mesa Boogie, Guytron, Rocktron, DOD, Summit Audio, and Smokey. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4AB3C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Accutronics Reverb Tank, 17' long, 2 spring, 4AB3C1B current production. Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Primarily used by all Fender® amplifiers with tube reverb from 1963-1990. Also used in Reissue models like: Fender® Princeton Reverb, Fender® Deluxe Reverb, Fender® Vibrolux Reverb, Fender® Pro Reverb, Fender® Super Reverb , Fender® Twin Reverb, Fender® Quad Reverb , Fender® Super Six Reverb,Fender® Vibrosonic , Fender®`63 Reverb Unit Reissue, Fender®`65 Princeton Reverb Reissue,Fender®`65 Deluxe Reverb Reissue, Fender®`65 Super Reverb Reissue, Fender®`65 Twin Reverb Reissue, Fender® 65 Twin Custom(TM) 15, Fender® Concert II, Fender® Dual Professional. Also used in Mesa Boogie® MK2C and others, LAB Series L5, L7, L9,Koch® Powertone I, Ampeg® VT-40, Ampeg® Super Rocket SR212 and B-52® AT-100. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Accutronics products are made in South Korea. Part #ACC-4AB3C1B | $35.99 | ||
Click on photo for larger view | Belton Reverb Tank, 17' long, 2 spring, 4AB3C1B, current production. Belton part number BL2AB3C1B. Input impedance 8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Primarily used by all Fender® amplifiers with tube reverb from 1963-1990. Also used in Reissue models like: Fender® Princeton Reverb, Fender® Deluxe Reverb, Fender® Vibrolux Reverb, Fender® Pro Reverb, Fender® Super Reverb , Fender® Twin Reverb, Fender® Quad Reverb , Fender® Super Six Reverb,Fender® Vibrosonic , Fender® 63 Reverb Unit Reissue, Fender® 65 Princeton Reverb Reissue,Fender® 65 Deluxe Reverb Reissue, Fender® 65 Super Reverb Reissue, Fender® 65 Twin Reverb Reissue, Fender® 65 Twin Custom(TM) 15, Fender® Concert II, Fender® Dual Professional. Also used in Mesa Boogie® MK2C and others, LAB Series L5, L7, L9,Koch® Powertone I, Ampeg® VT-40, Ampeg® Super Rocket SR212 and B-52® AT-100. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Belton products are made in South Korea. Belton part number BL2AB3C1B. Part #BL-4AB3C1B | $32.99 | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB2C1B. Input impedance 150 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4BB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB3C1B. Input impedance 150 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting. Upgrade for Crate part number 79-201-02 - tank for the Crate V-32 Palomino and Vintage Club 30 / VC3112. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4BB3C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB3C1D. Input impedance 150 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for vertical mounting, connectors down. Common replacement for MarshallTM, Ampeg, Crate. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4BB3C1D 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4EB2C1B. Input impedance 600 ohms, output impedance 2250 ohms, medium decay (1.75 - 3 seconds), input insulated/output grounded, designed for horizontal mounting, open side down. Common replacement for Ampeg, Crate V50 Palomino. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4EB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2B1A. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input grounded/output insulated. Mounts horizontal, open side up. Common replacement in vintage Ampeg. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2B1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2D1A. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input isolated/output isolated, designed for horizontal mounting, open side up. Used in some versions of the Ampeg V4. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2D1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2D1B. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input isolated/output isolated, designed for horizontal mounting, open side down. Used in some versions of the Ampeg V4. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2D1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB2C1C. Input impedance 1475 ohms, output impedance 2250 ohms, medium decay (1.5 - 2.75 seconds), input isolated/output isolated, designed for designed for vertical mounting, long axis horizontal, connectors up. Common replacement for Ampeg VT-22. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB2D1C 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3A1A. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input grounded/output grounded, designed for horizontal mounting, open side up. Common replacement for certain versions of the Ampeg Gemini and also found in some vintage Kustom amps from the 1960s and early 70s. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3A1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3A1B. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input grounded/output grounded, designed for horizontal mounting, open side down. Common replacement for Ampeg and Music Man. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3A1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3D1A. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input isolated/output isolated, designed for horizontal mounting, open side up. Used in some versions of the Ampeg V4. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3D1A 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4FB3D1B. Input impedance 1475 ohms, output impedance 2250 ohms, long decay (2.75 - 4 seconds), input insulated/output insulated, designed for horizontal mounting, open side down. Common replacement for Ampeg and Music Man. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tankshere. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #4FB3D1B 'Bringing back the sound of vintage Accutronics tanks' | $34.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8AB2A1B. Short Tank, Medium Decay, input impedance 10 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8AB2A1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8BB2A1B. Short Tank, Medium Decay, input impedance 190 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down. Primarily used by Crate and Ampeg. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8BB2A1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8BB2C1B. Short Tank, Medium Decay, input impedance 190 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down. Primarily used by Rivera PUBSTER 25 & CHUBSTER 40 , Rivera Knucklehead Reverb, Vox® AC30, with solid state reverb as used in the Seventies, Ampeg® Jet II J12R, Crate® G212, Crate® GT212, Crate® Palomino V32 & V16, Music Man® RD50, Kitty Hawk Supreme, Marshall® G80RCD, Marshall® G100RCD. Upgrade for Laney® VC15 (part nr. 10006), Brunetti Singleman, Mesa Boogie® Rectoverb. Replaces Ampeg® / Crate® part number 79-201-02. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8BB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8EB2C1B. Short Tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down. Used in Crate, Fender, Peavey, Music Man. This is the most popular short tank. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8EB2C1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8EB2C1E. Short Tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts vertical wall, long axis vertical. Used in Crate® Tube Driver series of amps, such as the TD-70. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8EB2C1E 'Bringing back the sound of vintage Accutronics tanks' | $33.99 | ||
Click on photo for larger view | Revisit™ Reverb Tank, 9' long, 3 spring, equivalent to Accutronics 8FB2A1B. Short Tank, Medium Decay, input impedance 1925 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down. Primarily used in Crate Amps. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 2-year warranty details here. Part #8FB2A1B 'Bringing back the sound of vintage Accutronics tanks' | $33.99 In Stock | ||
Click on photo for larger view | Rubber mounting grommets for reverb tanks, package of four. Provides shock absorption for tanks mounted directly to the inside of a wooden amp cabinet. Mounting Hole Diameter = 3/8' Outer Diameter = 1/2' Part #RRG-4 | $1.99 (For a pack of 4 grommets) | ||
Click on photo for larger view | 3 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 3 feet long. Part #RC-173 | $3.95 In Stock | ||
Click on photo for larger view | 3 foot Extra Heavy-Duty Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Heavy duty thick cable, gold RCA connectors, excellent shielding properties, additional ground conductor provided. Part #RC-273 | $6.95 In stock | ||
Click on photo for larger view | 4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 4 feet long. Part #RC-174 | $4.95 In stock | ||
Click on photo for larger view | 4 foot Revisit™ right angle cables for Reverb Tanks. RCA at one end, stripped cable at opposite end. For connecting reverb tanks directly to a PC board via a soldered connection at the PC board end. Used by a number of manufacturers. Dual cable, excellent shielding properties, 4 feet long. Part #RC-374 | $4.95 In stock | ||
Click on photo for larger view | 5 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 5 feet long. Part #RC-175 | $5.95 In stock | ||
Click on photo for larger view | 6 foot Extra Heavy-Duty Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Heavy duty thick cable, gold RCA connectors, excellent shielding properties, additional ground conductor provided. Part #RC-276 | $9.95 In stock | ||
Switches | ||||
| FOOTSWITCH W/LED Sturdy metal construction, an aftermarket replacement from Revisit™. Works with the Crate VC3112 Vintage Club 30 and Crate VC5112 Vintage Club 50. Mono 1/4' Plug, 16 ft. cable. LED indicates condition of switch. Can be rewired internally to work with other amplifiers. Click here for wiring diagram. NOTE: Will not work with many amplifiers, even those that used LED's on the original footswitch, without rewiring. Electronics background suggested. Also - will generally NOT work with amplifiers which did not have an LED indicator on the original footswitch. Part #FBS-470L | $21.95 | ||
| DUAL FOOTSWITCH W/LED Sturdy metal construction, an aftermarket replacement footswitch from Revisit™. Works with the Crate BV120H Blue Voodoo 120 Head. Stereo 1/4' Plug, 16 ft. cable. LEDs indicate condition of switches. Can be rewired internally to work with other amplifiers. Click here for wiring diagram. NOTE: Will not work with many amplifiers, even those that used LED's on the original footswitch, without rewiring. Electronics background suggested. Also - will generally NOT work with amplifiers which did not have LED indicators on the original footswitch. Part #FBS-471L | $26.95 | ||
Click on photo for larger view | ORIGINAL Crate® PUSH SWITCH DPDT Mini Short-Throw Push Switch. Has 6 electrical terminals on bottom of switch (DPDT). Used for channel switching, level switching, FX switching, etc on the front panels of many Crate® amps from the 1990s to present. Found in the Palomino, BT50, and many other models. Original Crate® part number 88-302-02. Has actuator shaft of 2.7mm square. Part #88-302-02 | $4.95 | ||
Click on photo for larger view | ORIGINAL Ampeg® PUSH SWITCH DPDT Mini Short-Throw Push Switch. Has 12 electrical terminals on bottom of switch (2XDPDT). Used for pre-post switch on Ampeg SVT4-PRO. Original Ampeg® part number 88-303-02. Has actuator shaft of 3.3mm square. Part #88-303-02 | $9.95 | ||
Click on photo for larger view | ROCKER SWITCH, BLACK. Has 4 electrical terminals on back of switch (DPST). Non-lighted. 1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm) Part #SW-5072 | $3.95 | ||
Click on photo for larger view | ROCKER SWITCH, LIGHTED POWER, RED. Has 4 electrical terminals on back of switch.1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm). Internal neon lamp powered by either 125VAC or 250VAC. Used in some Crate model amps - but may not fit all. Verify the dimensions of the hole cutout in the panel before ordering. Also used on many Engl Amp models.Also replaces the # 700048-3159 power switch in most models of Furman power conditioners.ReplacesAmerican DJ part # Z-PDP/900-PS-Nfor use in the American DJ PC-100A PC-4 power centers. Part #SW-5075 | $4.95 | ||
Click on photo for larger view | ROCKER SWITCH, LIGHTED POWER, AMBER. Has 4 electrical terminals on back of switch.1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm). Internal neon lamp powered by either 125VAC or 250VAC. Used in some Crate model amps - but may not fit all. Verify the dimensions of the hole cutout in the panel before ordering. Also used on many Engl Amp models. Part #SW-5076 | $4.95 | ||
Click on photo for larger view | ROCKER SWITCH, LIGHTED POWER, GREEN. Has 4 electrical terminals on back of switch (DPST).1/4' push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. Needs rectangular cutout of 0.82' wide x 1.15' tall (21mm x 29mm). Internal neon lamp powered by either 125VAC or 250VAC. Used in some Crate model amps - but may not fit all. Verify the dimensions of the hole cutout in the panel before ordering. Part #SW-5077 | $4.95 | ||
Click on photo for larger view | SWITCH, CARLING SPST TOGGLE, ORIGINAL REPLACEMENT FOR 60's and 70's Fender® AMPS (POWER & STANDBY SWITCHES) Part #SW-495 | $4.95 | ||
Click on photo for larger view | SWITCH, CARLING DPST PROGRESSIVE TOGGLE (OFF-STANDBY-PLAY) Replacement for amps which use a single toggle switch for both power and standby. Or, may be used to engineer a modification to amps which have a toggle power switch switch, but do not offer a standby switch (such as the Peavey Delta Blues, Fender® Blues Junior, etc). Seewiring information here. Part #SW-520 | $7.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - Rated at 20 Amps (125VAC) or 15 Amps (250VAC). Fits 1/2' chassis hole. Solder terminals or 1/4' push on, single pole / single throw (SPST). Two position - on/off. NOTE: RATED FOR AC SERVICE ONLY AT 250V MAX - DO NOT USE AS A GUITAR AMPLIFIER STANDBY SWITCH. Part #STS-20 | $3.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - MADE BY CARLING Rated At 15A/125VAC, 10A/250VAC. Two Position (on/off), Double Pole (DPST). Fits 1/2' Chassis Hole. Solder Terminals Or 1/4' Push-on. Fender® Part Number 0036570000. Part #SW-525 | $6.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - Made by Carling®- rated at 15A/125VAC, 10A/250VAC. Two position (on/off), single pole (SPST). Fits 1/2' chassis hole. Solder terminals. Part #SW-526 | $4.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - RATED AT 10 Amps (125VAC) or 10 Amps (250VAC) - TWO POSITION (ON/ON). Fits 1/2' chassis hole. Screw terminals, or remove screws for soldered connections. Double-pole double-throw, no center off - two positions (ON/ON). Part #STS-10-DPDT | $3.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - RATED AT 15 Amps (125VAC) or 10 Amps (250VAC) - TWO POSITION (ON/ON). Fits 1/2' chassis hole. Screw terminals, or remove screws for soldered connections. Double-pole double-throw, no center off - two positions (ON/ON). Part #STS-15-DPDT | $4.95 | ||
Click on photo for larger view | SWITCH, STANDARD SIZE TOGGLE - RATED AT 15 Amps (125VAC) or 10 Amps (250VAC) - THREE POSITION (ON/OFF/ON). Fits 1/2' chassis hole. Screw terminals, or remove screws for soldered connections. Double-pole double-throw, with center off - three positions (ON/OFF/ON). Part #STS-15-DPDT-CO | $5.95 | ||
Click on photo for larger view | FOOT SWITCH, CARLING BRAND, SPDT, LATCHING Found in many type of footswitches. Has 3 electrical terminals (single pole, double throw). Solder lugs for wire. Part #FS-492 | $9.95 | ||
Click on photo for larger view | FOOT SWITCH, CARLING BRAND, SPST, LATCHING, REPLACEMENT FOR Fender®, ETC. Carling SPST footswitch. Used in Marshall® etc. Reverb/tremolo/channel switching pedals.Has 2 electrical terminals (single pole, single throw). Solder lugs for wire. Part #FS-493 | $9.95 | ||
Click on photo for larger view | FOOT SWITCH, DPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS. Double-pole Double-Throw, made for direct connection to a PC board. Has 6 electrical terminals. Part #FS-498-PC (Also see our complete line of switches) | $3.95 |
![Ampeg Ampeg](/uploads/1/2/6/0/126060472/565259278.jpg)
Ampeg Svt 15t Manual Treadmill
Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. the replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. the distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.
Ampeg Svt 15t Bass Combo Amp
Copyright ©2019 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
WARNING: these products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov